Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hey all
I've some basic question about the Call-Stack.
In my application I have a series of functions which call other functions and so on until an depht of about 20 calls...
Hello. How i can do a simple read an 0 -> 3 Volt (vdd) signal on Analog 0 P0.03?
I try it with saadc without sucess
int result = 0;
NRF_SAADC->CH[0].CONFIG = (
...
Hi everyone, I know that this topic has been mentioned before, but there are a lot of doubts and the situation about measuring a battery is still not clear.
1) First of...
Hi,
Here i are using nRF52832 ,softdevice S132 and mesh sdk v3.0.0
I am facing an issue in UART configuration in mesh (LIGHT SWITCH EXAMPLE) server code . When using my...
Hi all,
I am building Border Rounter and Thread Network. I using SDK 3.1 and image newest for border rounter
I follow this link https://infocenter.nordicsemi.com/topic...
Hello. I am working on a application in a NRF5238 with s132, where I send 20 byte packets using notifications from a peripheral to a central board. The central is a modified...
I updated to SDK v1.0.0 today and have not been able to build sample or application solutions since. I updated the SDK, modem FW, and SES.
For example, when I open and try...
Hi,
I'm sorry to borther you in your holiday.I got a issuse about 52810 (s112) with PA.I found my device would reset when I call ble_advertising_start() after calling pa_lna_init...
I'm trying to implement Serial Wire Debug to read some Data from Nordic from other Controller. Initially Need to read some registers in DP & AP Nordic. For that I need to...
Hi guys, i was using nrf51822 s130 sdk, and now i am using nrf52dk s132 sdk. When i am using nrf_adc.h, all bitfields macro's get errors. It's bitfield macros doesn't match...
I am trying to connect BLE app to BLE Device ( NRF 52840 ) and for security purpose, I adding passcode (password) / key in the device, once I am going for connecting it will...
I used serial program to talk between nrf52 and arduino where the rx tx pins were default 8 and 6.When i changed the pins to 25 and 26 it is not working i am not able to communicate...
Hello
I'm looking for someone to help write a custom bootloader which performs FOTA update by using an HTTP connection to collect firmware. NRF52 is connected to GSM module...
Hello, Dear Support!
I explore examples in SDK 15.3.0 : ble_app_hrs and ble_app_rscs. The peripheral device in ble_app_rscs is configured to wait active request from central...
