I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
i am using nrf52840 USB dongle and the segger J_LINK EDU mini for debugging when i use bulid and run it works, and if i remove the donle and reinsert it then ts not working...
Hi,
I was using nRF command line tools 10.14.0 before. i try to update to 10.15.1 but fail with below log.
Do you have any comment for us to overcome this issue? ...
Using NRF Connect for Desktop V3.9.1 for Windows. We flash custom boards with J Link EDU 9.4 version. Since update to Programmer v2.0.1 it will not detect the J Link. Any...
Hi,
ncs1.8.0\zephyr\samples\bluetooth\periodic_adv\
ncs1.8.0\zephyr\samples\bluetooth\periodic_sync\
periodic_adv and periodic_sync
how to change to use Zephyr controller...
Hi,
I have a nRF5340 with USB DFU support which uses MCUBoot for upgrades. The current build (app_version_1) on the nRF has 0x4000 as the size of the settings_storage. The...
Hi,
Developing by NCS SDK, We found it will take 20 minutes by using mcumgr(on MacBook-pro) to BLE OTA 178KB image to nRF52840 Product Board's external SPI FLASH. it success...
The following is my set up:
platform: windows 11,
editor: visual studio code with nRF connect
SDK: nRF connect SDK v1.8.0
toolchain: nRF connect SDK v1.8.0 toolchain...
Hi,
Here is my hardware.
VBAT is 3.6-4.2V, UWB_EN is Pin28.By using nrf_gpio_cfg_output( UWB_EN ) to init this IO.
Is there any problem?Because when I using nrf_gpio_pin_clear...
Hi,
my product now is base on the nrf5340, I want to set the USB's serialnumber same as the ble mac address.
when I use the nrf52840, I can set it as follows simply. ...
Dear all,
My objective is to have an external MCU send data to an nrf52840 via UART and directly send this data via BLE to another nrf52840. I started from the ble_app_uart_c...
Hi,
I am developing an ANT TX application using the nRF52832 and SoftDevice S332. Things seems to be working well ... but I need one clarification As per the ANT example...
I am running the NRF52832 (BMD-300 module) and I'm trying to talk to battery over SMBus.
SMBus is compatible with devices up to 100 KHz.
I was wondering if there was a...
Hi,
nRF5340_PS_v1.0.pdf has multiple PIDR2 values to denote engineering versions of the chip. This seems to have been removed in subsequent product specifications, and now...
Hello, I tried to use pin_change_example in SDK to catch Interrupts (at first line) but I'm missing lots of them.
How can I catch all the interrupt events without delay...
