I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hello.
This issue was tested with nRF5 SDK v17.0.2.
There are steps to reproduce :
sdk_config.h should not be included in nrfx_clock.h. It's a default template by...
Hello,
I am looking for some help solving a peculiar issue with eddystone beacons, the nRF52805, and some cheaper Samsung android phones.
System Description: - I am using...
Hello,
I have been running this program without any problem then I added some code to read and write to flash using NVS when the error shown below appeared.
I am running...
I have been using the Toolbox to load zip files to a device. Now the toolbox uploads a file and 'say it is complete', but the file status in the menu window say file not loaded...
Hi forum,
I am working on nrf52832,using sdk15.0.0.
I referred TWI_sensor example as reference for sesnor interfacing. Individual sensor works when i trired to integrate...
Hi,
I am using an NRF 51422 DK, SDK 12.3, and Soft Device S130. I am also a beginner to development with Nordic Products, and RSSI collection in general. I am using the...
Hi Nordic team, I'm working with nRF52840 PCA10056 , base on Thread_Zigbee_ v4.1.0 , and light_control example. I modifed, try to add temp_measurement ZCL in all light_bulb...
Hi ,
My environment:
nrf5340 dk board
nrf connect sdk
segger studio IDE
.
I want to test spi loop back without any connections.
I don't want to connect any...
Hello, zephyr pwm driver documentation and samples , shows clearly how to generate a PWM output using nrf52840 dk. However, we need to synchronize the PWM output to an input...
Hello, how can we configure the counter in an nrfx52840 dev board to count pulses on an input pin in zephyr? There is a counter driver in zephyr, but there doesn't seem to...
What I'm trying to do, is probably very simple. I hope.
In the following code which works fine.
I want to scan not using Coded PHY
Then change back to using Coded PHY...
question here, I am using nRF52840 device with zephyr application & MCUboot + SMP service the DFU is now done using: https://github.com/apache/mynewt-mcumgr-cli or using Nordic...
I have a application using 52805 with no external crystal, I found that Timer1/2 not working, anyone have idea can Timer run with internal HFCLK(HFINT)? by the way, everything...
Hello i am trying to send 4 bytes of data over ble with custom service but im getting an unknown error and i am stuck in a dead end please help me .I am greatfull to any kind...
Hi,
I try to change the endianess of transmitted data from Little Endian to Big Endian.
So for example when I want to transmit a value uint32_t valueTx = 0xAABBCCDD
...
