Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi Team,
For my project, I am using nRF 5340 board and using the Zephyr SDK for development. I need to read and write data from/to an external SPI EEPROM used ( MP95P08...
Hi,Team,
I am currently using the nrf54l15-dk to debug NSIB. The version of my NCS is v3.0.2. I referred to this link: https://docs.nordicsemi.com/bundle/ncs-2.9.0/page...
Hi,
We have sent out our product (includes the nRF9160 SiP and an nRF52840) for EMC testing and the test lab is asking for the following:
nRF9160 LTE Cat M1 and NB...
I am trying to set the charge current (ICHG) to 100mA or 200mA using nPM1300 on nRF52832 via TWI (I2C). However, the measured current is always limited to ~87mA, even when...
Dear Nordic Support Team,
I am currently working with the nRF9160 and exploring secure methods to lock and unlock the device without losing the firmware.
At present, I...
Following the instructions from
https://docs.nordicsemi.com/bundle/asset-tracker-template-latest/page/common/getting_started.html
I get build errors building the asset...
Hello Team,
We are currently working on the nRF54L15 platform and using nRF Connect SDK v3.0.2. We've successfully added support for DFU over BLE using the following steps...
Hi, I am working on a project where ECG data can be send wirelessly. For that I am using ADS1298 and nRF52833. I am very new to it. I have connected the nRF52833 SPI lines...
Hello all,
I'm using nRF5_SDK_17.1.0_ddde560
Examples folder:
...\nRF5_SDK_17.1.0_ddde560\examples\peripheral\twi_sensor
...\ble_peripheral\ble_app_blinky
Are...
Hi, I created a blinky sample for the ProMicro board. Entered the flash mode as mentioned in https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/boards/others/promicro_nrf52840...
Hello ,Nordic
Our product uses the Nordic nRF52832 chip, and we recently encountered a device with an anomaly related to FDS writes to Flash. We are using nRF5 SDK version...
I am using NRF SDK 17.1.0
I inherited some legacy code that was a mess, and rewrote it.
Part 1 -
First I skipped the peer manager thinking it was not necessary. Then...
I am debugging my custom nrf54L15 board, and want to use the nrf54L15-DK to flash and debug the board. My SWD debug probe and cabling was used for a previous version of the...
For VDD-nRF in the nRF54L15-DK schematic When I check the schematic, I can't tell which part is internally generated.
When I check the actual board, VDDM_nRF and VDD_nRF...
