Hi, I am Product Manager working for Medical Device Manufacturing company based out of Ireland.
we are in search for a development house / developer who will support us...
I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
Hi,
when debugging BTmesh (with MPSL) breakpoints trigger an assert. This is listed in the known issues of the nrfConnectVScode page:
https://nrfconnect.github.io/vscode...
Hello, i'm trying to flash a code in my module nrf52805 thx to my Dk nrf52840. i have this error I followed the instructions here: https://devzone.nordicsemi.com/guides/short...
Hello,
I want to build a configuration where MCU Boot secondary partition is in the external flash and QSPI data encryption is turned on.
I modified the nrf_qspi_nor...
Dear, I want to interface nRF5340 to normal 16x2 Alphanumeric LCD running on 5 Volt. Are the Port pins of nRF5340 5 Volt compatible when nRF is running with 3.3 Volt supply...
Hello,
After succesfully configuring the W5500 driver using Zephyr, I am trying a few examples in the given samples (socket echo). I am unable to send or receive / ping...
On the nRF5340 P0.00 and P0.01 are used for the 32.768 kHz crystal by default and are not available as GPIO on the connectors.
how to remap this pins to gpio?
I need to develop a pair of BLE-capable devices that talk to each other. The communication between them will be very simple - the central needs to tell the peripheral the...
Hi,
When the NRF9160 boots the GPIO level of a given pin, such as P12, is set to high (3.3V) before the main application gets a chance to call gpio_pin_configure and gpio_pin_set...
I am now using the DFU functionality to upgrade the code combined with the CoProcessor and radio_test samples and find that the code takes up too much space to upgrade. I...
I recently bought Thingy:91 (nrf 9160) there was a SIM card included but it didn't work! I have written to support twice at the recommended address [email protected]. it was...
Hello,
I am using PCA10040 DK for the programming with ble_app_beacon_pca10040_s132 example code. I want to broadcast my 20 bytes of data with my 0xFFE0 UUID.
In this...
Hello,
I am using the nrf52840dk_nrf52840 with NCS v1.7.0. I am trying to use the external memory (MX25R64) to host the mcuboot_secondary slot. Then, the primary slot...
Hi, I have recently acquire an nrf52840 development board to prototype a usbd msc. With the example provided in sdk17.02-USBD_MSC, for saving every 1000 frames of data, 100...
Hi
I want to konw what will softdevice or ble do after the chip enters system on mode.How do I know which components are working during advertise and connection intervals...
I am using the MDBT50Q-1MV2 which has the nRF52840, and have burned the Adafruit Feather Express bootloader using a J-link and the Arduino IDE. The issue is that I have not...
