Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
I want to use the register of Nordic's P0 port directly to set 1 or clear 0. Like this,
p_reg-> OUTCLR = clr_mask;
P_reg - & gt; OUTSET = set_mask;
p_reg-> OUTCLR...
Currently we are developing against hardware sensors etc. that we have installed in our warehouse
It would be great to be able to develop remotely (ie. from home) without...
Hello Nordic Support Team,
I'm using nrf52840 DK for DFU update over ble with nrf5 sdk previously it was working fine and i was using nrfutil tool to generate settings,...
Hi,
I have downloaded the nRF5 sdk v17.1 and used the peripheral blinky example with pca10056e and S112 soft device and modified the preprocessor defines and this example...
Hello Everyone,
I am working on NRF52840 and we had enabled the APPROTECT feature in our firmware. The code for implementing this is as follows:-
void init_mem(void) ...
Hello,
I know that the bt_ctlr_set_public_addr() interface needs to be called before enabling Bluetooth, and this bt_id_create() .
But I read the description of bt_id_create...
Hi,
The nPM1100 Specification states in section 7.2 that:
An application should not be supplied directly from VBAT because it can disturb the battery charging process...
Hi everyone,
I wish know how i can set BLE_GAP_TX_POWER_ROLE_ADV at peripheral and BLE_GAP_TX_POWER_ROLE_CONN at central on UART example provided on nRF Connect SDK v1.6...
Hi All,
I am working on a nRF52832 project using SDK 17.0.2, SD 132 and a custom board. I added secured bootloader functionality according to example. At start of the main...
Hi everybody,
I am with two custom oards that include nrf52840 chip, one acting as central and one as peripheal.
This example is custom to get multilink, for that i save...
Dear team ,
i am working on ble_app_lbs_nus_c project when in this project try to add nrfx_timer.c file
we got an error like this.
Building ‘ble_app_lbs_nus_c_pca10056_s140...
I was reviewing the MNO certifications, and I see that there have been no updates since 1.5.1.
1) Is it acceptable to use 1.6.1 with AT&T?
2) Is certification planned...
Hi, I am trying to update the battery level through an example of the HID keyboard of nrf52832.I'm trying to connect 3.3V battery to SAADC AIN0, but as shown in the picture...
Hi, I have a question about nRF Connect Programmer tool.
[Description]
The device memory layout shows the address range as "0x00000000 - 0x00100000 (size 1048576 bytes...
