Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hello.
I'm going to make a prototype board and use it soon. I will make a prototype board with nrf52840 and use it soon.
It's my first time developing a prototype board...
nRF sniffer: v3.0.0
Wireshark: v3.2.6
Hardware: nRF52840 ( PCS10056 )
wireshark did not show packets with MTU greater than 20 bytes, is it still not supported?
Hello ,
We are using the following.
Module: Bm833 (nRF52833) from Fanstel
Softdevice: S140 7.0.0
SDK: nRF5SDK17009d13099
Sample code: ble_app_uart
We have added...
Hi, We are developing a BLE app on nRF52840. For the next step, we want to try reading/writing to other devices through connector interface on nrf9160 dk. Is it possible to...
I followed the steps below: flash softdevice flash bootloader
generate package
flash package
But after that I can't connect to this board by using usb and need again...
Dear Team,
I am totally new to NRF24LE1. I have bought 6 pieces it through online. Iwant to program it using HAL libraries. I've searched it everywhere I ca do. But I...
Hello, everyone.
I use the ble_app_uart on the nrf52DK board and SDK V17.
I would like to send data from the app using RX characteristics of UART service. The function...
Hi all.
I have written an application using a softdevice and I want to analyse an interesing behavior I don't understand at the moment. So I want to record a trace/log of...
hi!
Can anyone help me with code merging of saadc and ble uart.
Basically i have done analog to digital conversion of my sensor value and monitoring it on serial monitor...
Good day,
Studying the possibility of using C ++ on the MCU nrf52840, I met an interesting moment in file "nrf52840.h"
I have added a part of the file which gives me some...
Dear Nordic Semiconductor support team.
I tried to make my nrf51822 DK to talk to Micro:bit by using Gazell library. ( from nRF5_SDK_12.3.0_d7731ad\examples\proprietary_rf...
I am using nrf52832 with buttonless DFU ,SDK 15.0,using fstorage.I want to store some device information in flash,such as serial number,hardware version,these data will not...
In the compatibility matrix , Engineering A must use the "nRF5340 OPS v0.5.0" specification but when clicking on it, only the latest version (0.6.1) is available.
Which...
Hello,
I want to add control over UART to ble_app_blink_c project.
SDK is version 16,I copied <SDK>/examples/ble_central/ble_app_blinky_c folder and made <SDK>/examples...
Hello,
We're experiencing a strange issue where a device we sent to a partner in the US wasn't able to connect over there after rigorously testing this before shipping here...
