Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
We are planning to base a GATT and LE Audio design off of the latest nRF Connect SDK v2.6.1 and looking into Bluetooth certification. I have found the QDIDs for the Host and...
Hello,
I am trying to use SPI driver to read BMI270 IMU data on my nRF52840dk. I stucked at verifying the sensor ID step. According to the datasheet, sensor ID is stored...
Hello,
I tried to read and write the OTP region in UICR of nRF5340 with nrfutil, but got the following output:
Any Ideas, what could be the issue here? Does nrfutil...
Hello, After consulting the manual and understanding the composition of the calibration data page, the ant_bpwr_calib_handler was added, but the callback function was not...
Hello, I want ro test the channel sounding feature using the new nRF54L15-DK /PDK and I found a sample example for reflector role - "https://docs.nordicsemi.com/bundle/ncs...
I'm migrating an nRF52840 project from ncs 2.7.0 to ncs 2.8.0. We pass the board in to the west build command line. Our CMakeLists.txt uses the BOARD & BOARD_QUALIFIERS to...
Hi,
I am refering chapter 3 of "nRF connect SDK Fundamental" . ( Configuration files - Nordic Developer Academy )
I am refering few samples like "blinky_pwm", "peripheral_lbs...
Hi,
We are currently planning to start a project using the nRF52832 as our controller, SEGGER Embedded Studio version 5.42a as the IDE, and nRF5 SDK version 17.0.2 as our...
The scan window does not alternate properly with the BT_LE_SCAN_OPT_CODED option in the scan parameters. Specifically, the scan window does not toggle on and off every 30...
Hi. I want to report 2 observed bugs about board creator wizard of NCS 2.8.0.
1. When you click on "Create a new board", the first thing that you must enter is human-readable...
I'm trying to activate low power mode without success. I found samples but it appears not to work with the last NCS version. I want to get basic GPIO INPUT values at 32khz...
Hi,
1. I am testing nRF54L15 PDK PCA10156 0.8.1 Example is: ncs\v2.8.0\nrf\samples\bluetooth\direct_test_mode 2. Which pins can be used as UART TX and which pins can be...
Hi,
We are currently planning to start a project using the nRF52832 as our controller, SEGGER Embedded Studio version 5.42a as the IDE, and nRF5 SDK version 17.0.2 as our...
Trying to set up UART/UART0 for async. I cannot get the uart interrupt config to shut off.
CONFIG_UART_INTERRUPT_DRIVEN =n is set in the prj.conf
In config output...
Maybe the title doesn't make that clear.
First of all, I have customed my own nrf54l15 board, and I successfully built and run some ncs demos.
Now, I want to do something...
