Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi
Can anyone tell me which example in SDK to use to send data(a simple text message) from nRF52832 board to an Android Phone. I have nRF Connect and nRF Tools applications...
HI,
I've noticed a few issues with the example app_level.c.
1: The g_set_transition() was updated in the 3.0.0 release to avoid a division by zero, however, this fix...
Hello all,
I recently migrated from SDK 15.0.0 to SDK 15.3.0 and as a result tried to migrate from SD 6.0.0 to 6.1.1.
My application goes to sleep after a while and when...
I am new to this environment.
Attempting to create a simple BLE app similar to the built-in BLE, but with some buttons to send predetermined commands to devices. Using the...
I applied Bonding to the UART example(ble_app_uart).
Bonding combined with the UART example works well, but there is one problem.
1. I did Bonding first. 2. After that...
Basically I get an Attribute not found error from sd_ble_gatts_value_get() in the nus_ble.c and then I never get any NUS events in the application. I'm trying to figure out...
Hi!
We have working solution with custom rf protocol based on NRF52832 and NRF52840(now it use 2 Mbps Nordic proprietary mode). Now we want improve it.
Could You give...
HI,
I have found some problem with nrfutil (version 5.2.0 installed from pypi).
Problem description:
When I am updating dfu with success (correct keys, packages etc...
Greetings,
I'm using 3 NRF52832 boards, s132 and SDK 14.2.0. I'm interested in connecting two hrs peripherals to a single hrs central, but have found some posts that say...
When creating an attribute specifying vloc as BLE_GATTS_VLOC_USER, it is not very clear that a storage pointer must be provided on creation of the attribute and cannot be...
Hi,e verybod, I use nrf51822 to do bluetooth keyboard, I hope the function is: After bluetooth keyboard connect the host,how to determine whether the connection is window...
I'm trying to create a virtual beacon on an Android Phone using nRF connect V4.22.3. Android Version on the phone is 8.1.0.
I've enabled a beacon using Advertiser. However...
In an BLE example I have a characteristic with the value 0x00001234. In the nRF Connect 2.0 for iOS i see the value 0x00001234 and in nRF Connect for Desktop v3.1 i see "34...
Using the logging module in ncs v1.0.0, I see some extra characters after the timestamp " <0x1b>[0m<inf>" and at the end of the line ", is there a way to fix this?
The terminal...
