Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
I'm using nrf52832DK with seggers studio and SDK 14.2. My settings are following.
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(20, UNIT_1_25_MS) /**< Minimum acceptable connection...
AIM: To establish a mesh network having 3 nRF52840 dongles and end devices(mobile phones) will be connected to the dongles. The primary aim is to send data(string/number)...
Hello
We cannot use the P0.18 pin as standard GPIO on the nRF52840 Dev. Kit.
What are the actions HW / SW to do to use this pin as standard GPIO ?
Should be cut...
I try to set up a timer:
The nrfx_timer_init() function crashes with an error:
What is wrong? How to fix this?
Environment: nRF52840, NRF SDK 15.2, S140 6.1, Mesh...
hi all
how to test 2.4G(not ble) at nRF52832 platform?i need test the 2.4G signal performance include tx power , sensitivity , frequency and so on.i use nRF GO studio.but...
I'm trying to understand the best way in which I can maximize the data throughput on an nRF52832.
I am using a custom circuit board which is running an early version of...
Hi,
I'm using Segger Embedded Studio with Ubuntu, trying to write a minimal code to let the chip start advertising.
I tried to read and understand the example codes provided...
Hi team,
customer used SDK v15 and the default s140 softdevice in it.
When the 52840 is configured in the 2M phy mode after connecting with Iphone 8/x, it can't be successfully...
Dear Sir,
Currently the example code in "ble_app_hrs" is written such that it advertise in connectable mode.
How can I modify the code so that it advertise in NON_CONNECTABLE...
Dear Sir,
I am talking with respect to the ble_app_hrs example in the SDK 15 for nrf52832. I am using softdevice S132.
In the example the code is implemented such that...
For instance, if I wanted to download the firmware that comes on the nRF52840-dongle in order to then write it to a custom board with an nRF52840 chip on it (i.e. so that...
Good morning,
I can't import the nrf_serial library ( and nrf_queue ) on the ble_app_uart project, after that i compile, i read these errors :
linking... .\_build\nrf52840_xxaa...
Hi,
I'm using 2 nRF52832s in my project. One of them is connected to a PC serially and has NUS central running on it and the other nRF52 connects to this central. I was...
I have two 52840DK, which can be used before, but I took it out and used it today. The led light on the rear panel of the USB is not lit, and the computer can't detect the...
Dear Sir,
I was trying to implement the following scenario.
Multiple phones initiate the connect request to a single peripheral.
On peripheral search for the phone...
