Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Dear all，
We use thingy's microphone collect data and transmit to Android mobile by BLE, and need no loss of reliable data transmission.
How to do?
Thanks a lot.
I have developed custom PCB with nRF52832. My antenna layout is very similar to layout present on nRF52DK (PCA10040). All works well. Now, in next prototype, I want to add...
I designed the NRF8001 into my circuit board and my application processor is connected to it. Now I need to develop my application program such that I can transmit and receive...
Hi,
I am working with the Red Bear BLE Nano 2 (nrf52832) and programming it in Arduino IDE .
I am trying to merge the BLE_HRM example with a TWI example to be able to...
Hey,
I have a problem with receiving data on my Android app.
I'm sending several data via Services & Notfication Characteristics from my NRF52840 Application to my Android...
hi,
I have some problems about pwm register.
1.NRF_PWM0->MODE
2.NRF_PWM0->COUNTERTOP
3.NRF_PWM0->LOOP
4.NRF_PWM0->DECODER
5.NRF_PWM0->SEQ[0].PTR
6.NRF_PWM0-...
I use rRF52832. After doing "Flash Tab -> Erase" of Keil's development environment, it became impossible to connect at all. I tried using nRF 5x Command Line Tools (nrfjprog...
I'm trying to port the _12.3.0_ DFU bootloader_secure example to my custom nrf51822 board.
The example can run perfectly on pca10028 board, but not on my 51822 board even...
Hi All,
I am developing an application on nRF52840 Preview DK which does not need the Soft device. But it needs the MBR to run a bootloader for Firmware update purpose....
Hi,
Now I am using nRF52382 to make a product which needs a accurate one second timing. Then I use the project "nRF5_SDK_15.0.0_a53641a\examples\peripheral\rtc" and "nRF5_SDK_15...
Hi there!
Device: nRF52 DK
App: nRF connect
Compiler/IDE: Segger Embedded studio
SDK version: 14.2
Soft device: s132
Problem description: I am trying to run blood...
Hi,
I am reading a BMX055 via I2C which consists of three sensors with three addresses.
I got the easyDMA running to read 10 times the gyro using the PPI and the data...
Hello,
my first question is about TX carrier frequency accuracy measurement. The equation given in the whtie papers is
(|f_measured - f_programmed|) / f_programmed <=...
Why is the event length of the BLE Central HRS demo set to such a high value of 320*1.25ms = 400ms?
The demo seems to work ok with the BLE Peripheral HRS demo using the...
