Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
We are developing a USB ANT dongle with nRF24AP2-USB chipset, but we meet a problem when use CW test with ATWareII tool.
We set 2.466GHZ, but we see 2.271GHZ mark, but...
Hello,
My code( I add a source code lower ) has error on bold line printing NRF_ERROR_INVALID_STATE. The program uses three timers and init by "MAX_TIMERS = 6" and "OP_QUEUE_SIZE...
Do anyone ever measured current consumption of ble_app_uart?
What is current when connected and uart idle, transmitting, receiving, and transmitting while receiving?
Please...
I tried changing the define below from 1 to 2, so I could have one handler for a button and a different handler for other sensors. But my problem is:
If I set it to...
Hello,
I've developed a circuit with Mikroelektronika's nRF T click module. This module uses nRF24L01P but as I see I cannot order it because it is obsolete.
Should...
We plan on use the ST BAL-NRF01D3 balun for a PCB with both an nRF51822 and a nRF51922 on the same PCB separated by about 4 inches.
Should we use the PCB antenna as on...
Hello.
I am very confused with memory layout of nrf51822 BLE examples using SoftDevice stack.
Some examples set IROM1 range from 0x0 to 0x3ffff. (ex, ble_app_advertiseing...
Hi,
I have a nRF51422-EK board (Rev. 1.0) that is bricked.
When connected the LD3 is on.
Jumpers are present on P8 and debugger.
Device manager (win7) assigns...
Hello,
I was puzzled by RM.
I notice POWER control register in peripheral(UART,SPI,TWI) module.
Please answer following questions about the relation between system...
I download the softdevice for PCA10001. And I want download another program, but it didn,t work. The problem I have attached here. As you known, I have push the button 'recover...
We plan on using the external 16 MHz and 32 KHz oscillator inputs to reduce BOM costs since our host micro uses a 16 MHz and 32kHz crystal and it can generate outputs. If...
Hi guy:
I have buy nrf51822 dk .Why I can not download nRF UART App for Android 4.3 at below page www.nordicsemi.com/.../nRF-UART-2.0-for-Android-4.3
Thx
I made code like to below for using 16Mhz system clock.
/* Start 16 MHz crystal oscillator */
NRF_CLOCK->EVENTS_HFCLKSTARTED = 0; NRF_CLOCK->TASKS_HFCLKSTART = 1;
...
