Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Dear all,
For EMI/EMC Test, we need the USB UART CLI functionality for example "Radio Test",
could you tell us how to implement it or any example can do that?
Thanks...
I am using 3 axis LIS2D12H accelerometer interfaced with NRF51832 with SPI interface. The sensor has sampling rate from 1 HZ to 5.376 KHz which is happening at sensor only...
Please, share the firmware of the board nRF9160-DK PCA10090 version 0.8.5 , which is flashed into a new board. The firmware that I received using the instruction ( https:...
Hello,
I am using NRF52832(WLCSP package) and nRF5_SDK_15.2.0 for the product.
I also use IAR Embedded workbench 8.32.1 as IDE.
Few hundreds devices are assembled...
Hi,
I'm trying to figure out how to ping a specific IP Address from the nRF9160 via AT Commands. I can't seem to figure out how to do a simple ping to an internet server...
Hello! Board nRF9160-DK. Compiled and uploaded the project asset_trecker (merged.hex). The LTE Link monitor shows a cyclic reboot. LEDs do not blink. where is my mistake
Sorry,I want to know whate is the different between BLE_UUID_TYPE_BLE and BLE_UUID_TYPE_VENDOR_BEGIN, the Device name will become N/A when I use BLE_UUID_TYPE_VENDOR_BEGI...
Hi,
I'm studying the example about the nrf_crypto for implementing asymmetric encrypt and decrypt function.
The suggestion on the Dev_Zone is to use the share key to symmetric...
Hi,
Is there a possibility that the order of the responses can be different with respect to the order of the requests?
We check for the success status of the APIs sd_ble_gattc_read...
These two options in nrf_mesh_config_app are arbitrary for me if I don't understand how they should be sized.
From the documentation of the MESH SDK 3.2.0:
ACCESS_FLASH_PAGE_COUNT...
My app runs the following code, that is supposed to init the SoftDevice:
nrf_clock_lf_cfg_t clock_lf_cfg = { .source = NRF_CLOCK_LF_SRC_XTAL, .xtal_accuracy = NRF_CLOCK_LF_XTAL_ACCURACY_20_PPM...
Dear Nordic,
We have developed a product utilized the NFC readable/writable feature of NRF52832. We have tested it against some of the HTC, Sony, Samsung, and Google phones...
Hi,
I will add feature "installation codes".
I guess that security API do work.
At coordinator side, zb_secur_ic_add, zb_set_installcode_policy functions
At end device...
I am trying to implement nRF52 Light Switch Proxy Server in nRF52832 boards. Everything works fine on behalf of board and it prints the Device UUID as well. Although I can...
i'm using nRF mesh sdk v2.1.1 with 2 boards and 1 provisioner board. I have un-provisioned 1 board with the help of config_client_node_reset(). I want to know the procedure...
