Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi,
I am able to connect nrf51822 with nordic app but now i want to receive data from nrf51822. For Example -
If nrf51822 detects some voltage at pin no "1" then it should...
Are there any Segger Embedded Studio examples for the nRF51 dev kit?
All the examples supplied with the nRF5_SDK_14.1.0 seem to be for the nRF52.
I only bought a new dev...
How do you do
E: \ Nordic \ nRF5_SDK_12 _f012efa 2.0-3 d \ examples \ peripheral \ pwm_driver pwm_driver routines of the path,
1.How to configure reverse polarity...
In all the SDK examples all the source is in main.c. Is there a good reason for keeping everything including timer initialization, UART config, BLE setup, etc all in one file...
Hi,
I am using nrf51822 (pca10004) with SDK110 softdevice programmed through j-link LITE SEGGER. After programming the custom code (Basic I2C code) and when we try to debug...
Is there any documentation as to how to connect a nrf52 chip (as found on the nRF52832 BT Module with Header Pins ( www.analoglamb.com/.../) or the nrf51 on the Adafruit bleFriend...
Hello,this is Lee.I have a problem about nRF51822.
When I turn on/off the power 2.8V to it ,it hangs up
frequently.I check POR function,I found that the residual
voltage...
hi,
i'm using the 32KHZ external crystal and i didn't find any free space in my PCB to put the crystal in the same side with the nrf chip, so the only solution that i found...
I am trying to implement a bootloader with rewrite protection on nrf52840 with SDK: 14.0.0.
But it seems that there is no flash write protection registers in nrf52840.
So...
UPDATE: Corrected language.
Hi,
While experimenting with BLE mesh networking using S130 on nRF51 devices and S132 on nRF52 devices, we have a problem with deafness while...
Hello,
I want to save Image data which are come from the central device to flash memory of peripheral side.
The image data size is vary from 3KBytes to 10KBytes.
...
I just came across the following code ..
(hash)ifdef linux
toolchain_init_irqs();
(hash)endif
Does that imply there is a possibility that the source could be...
How can I running the ble_app_multirole_lesc example in debug mode to examine the traffic? I use me network traffic analyzer to view the traffic currently ((debug mode switched...
I want to use several sensors that makes a measurement send the data to server (same as provisioner) and fall asleep. Wake up after 20 minutes and process repeats.
Does all...
In server role:
Is there an event that fires after (or before) each advertisement?
I would like to use that to alter the local name after each advertisement, in order...
