Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
I'm using the ESB API and I've noticed some peculiar operation when debugging with nRF Connect. I have made the following observations:
1) Giving a semaphore in the ESB...
I'm using the Async UART API and the Enhanced ShockBurst API and my code seems unstable. The RF Connect Debugger frequently crashes.
The ShockBurst User Guide specifies...
Each time I attempt to use a Zephyr API on my NORDIC device, I face the mystery of what CONFIG setting are required to go with it. For example:
To make the Async UART API...
NCS 2.7.0 with Toolchain 2.7.0
I'm working on an out of tree application derived from the example application project.
I'm using sysbuild with MCUBOOT.
The processor...
Hello, we are using the NRF52810-QCAA in LDO configuration. On reference design, there is an NC decoupling capacitor on DEC2 pin.
Is it possible to completely remove it...
Hi,
Not sure if it's a zephyr issue or a LVGL issue, so I hope I'm at the right place.
I use an 1.54 eink display with the SSD1681 driver, and LVGL. Everything goes well...
Hi Nordic,
Board:nRF54L15 DK
Code Base:peripheral_uart
Issue: Added Zephyr NVS Flash support but encountered error -22 from nvs_mount(&fs). Additionally, data cannot...
Hi everyone,
I'm working on the nrf54l15 with the nrf sdk v9.0.0 wihch I assume integrate matter version 1.4. I'm using the google nest max as a thread border router....
I am developing on a custom nRF5340 board, but I encountered a BLE-related error. To troubleshoot, I built and flashed the basic example peripheral_uart , but the following...
Hi,
We are working with nrf53-DK evaluation board, and we are using P1.02\P1.03 pins for I2C communication.
We wanted to connect a 5V I2C slave on these lines can we connect...
Hello!
I am using an nRF Connect SDK V2.9.0 with a nrf54l15. I want to set up a project with a custom board. I want to add DFU in the future, so there must be MCUboot bootloader...
Hi everyone,
I'm currently working on a low-power application and aiming to minimize sleep current as much as possible.
Thanks to some great advice I've found on this...
Hey so I am making a capstone project with Drapers lab from University of Massachusetts Lowell and one of the requirements is to create an friendly end-user GUI instead of...
I want to confirm these questions,hope someone can give me some explaination.
1) RADIO has it's own kernal which is some kind of MCU.
I have looked through some doc on...
