Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Hi Supporter,
I use apptimer in proprietary_rf gzll, I used as below ,but it doesn't work.
1) app_timer_init(); ,here I ennable the RTC1 in the sdk_config.h
2)app_timer_create...
Hello NRF ,
I have been using NRF9160 DK GEN-1 board for NB-IOT and GNSS tracking and able to configure my network SIM as well as the NRF cloud .
I have used SDK 1.4.2...
Hello There,
Basically I just want to get Sensor data like (Temp Sensor) who already connect to Arduino and I get it , So I just want that data to nRF9160 over UART in...
Refer to nRF52840 Technical Manual USB 2.0 (full speed (12 Mbps) controller) The USB2.0 rate can be up to 480Mbps. We have a product whose USB transmission rate must not be...
I have created a program code on the Adafruit nRF52840 express in the Arduino IDE. I want to read this program code (including bootloader) via my j-link edu mini and save...
I noticed that the nRF Connect SDK has kept up with ZBOSS updates throughout the year. Is there a plan or recent releases with regard to the "nRF5 SDK for Thread and Zigbee...
Hi! I'm working on a custom board with nRF9160, I want to flash it with the asset tracker sample, however, I do not own a J-link device. What I have is a FTDI USB-UART converter...
My Thingy:52 is version 1.01. I haven't used it for a while and after charging, it didn't seem to be advertising. It was soft-flashing a green LED. I decided to program it...
Hi,
i am working on nrf52dk. i want to include "pwm" example in "ble_app_uart" example . i have included all the header files. and functions in "ble_app_uart" example. ...
Hi,
what is safe temperature range for nRF52840 - nRF9160 UART communication on 115200 baudrate without external crystals for HF clocks please ?
Thank you.
Hi,
I'm trying to program a custom board with a nRF52810 via nRF Connect. I keep getting the following error messages:
I followed this post and tried the following commands...
Hey guys,
I have nrf52832 custom Bluetooth module. It is stand alone nr52832 module . I just want to toggle any gpio on this module .
Can you guys tell me which library...
Hi all,
In my project, I make 2 SPIM and 1 UARTE works well.
Currently I want to use 1 TWIM, so I add lines below in proj.conf
However, I get errors: gen_isr_tables...
If nRF9160 stay almost all day in sleep, wake via RTC for a period of 1 minute and in this 1 minute period only make a GPS cold start, get the GPS coordinates and transmit...
My device is the slave, that is being connected (not always in the same order) by 2 masters.
I would like to create two different connection ways/points to distinguish between...
