Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic Team,
I am currently working with the nRF52832 on a custom board using nRF Connect SDK v2.9.0. I am implementing OTA DFU using Sysbuild and MCUboot with an...
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
Hi team,
We are going to kickoff a new project of 2-mic AI recording pen. Good to see we got a very high performance for 54LM20B with DSP/NPU, which might be a very good...
Hello,
We are currently developing a Zigbee product using nRF Connect SDK v2.8.0 . While reviewing the release notes for NCS v2.9.0 , we noticed two critical bug fixes related...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hi,
I can't seem to find any example code for nRF51822 on Nordic website. I can only find that softdevice. I am trying to use nRF51822 for some BLE functions.
Thanks,...
Hi Nordic:
It seems that mesh LPN can receive secure beacon via friend node, and if has no friend, LPN also can receive secure beacon if MESH_FEATURE_LPN_ACT_AS_REGULAR_NODE_OUT_OF_FRIENDSHIP...
I'm running some power tests on the nRF52 DK and, after fiddling with some of the power settings, I'm managing to get an idle current of about 1.8uA on the coin cell, and...
I'm sorry to ask a question that I'm sure has been answered before, but I can't find another post similar enough to be of help. I have an HID application that bounces back...
Dear All,
We are currently developing a low power application for the nRF9160, with ncs zephyr version 1.2.0. For our application we want to trigger an interrupt on both...
I Upgraded the software to V3.6.1. The button "Start DFU" is missing from the SFU mode screen. After choosing a Zip file there's nowhere to continue. Had to downgrade the...
Hello,
I'm developing an application using zephyr, openthread, udp, and nfc, targeting the nrf52840 (currently developing on nrf52840dk pca10056).
I initially developed...
Hi,
I would like to get some information about the reset's reason of my nrf9160 like
- The reason is due of an assert type "xxx"
- Where is the stack pointer
- .....
Hello,
I'm developing a BLE device and it consist of nRF52833 and a external UART component.
ble_app_uart example in SDK v17.0.0 is replaced app_uart to libuarte. The...
Hi,
I would like to know if we can enable codded phy while using mutli peripheral in conjunction with mutli central. Also peripheral should be scannable and connectable...
When creating dfu package using nrfutil, an error is displayed.
When I looked for and checked the file where the error occurred, a problem occurred in Python's max...
I am trying to run nrf52840 chip without debugger.
I want to run peripheral_uart example just to show advertising of bluetooth.
And when I use west debug --runner=jlink...
Hi,
I got a nordic thingy:91 and just play a bit with it and the asset_tracker application. Then I flashed the agps code because just want to send GPS coordinates on the...
I am having issues using port pin 1.00 on the 52840 as GPIO. It will just not toggle.
I can successfully use most other pins, even those on the higher port. For example...
Hi
I have 2 identical PCB just out of production - same FW - one is drawing higher current (about 600uA).
The issue is found in mass production and about 1% is having...
