Im working with:
-Windows Nordic Connect for Desktop App v5.20.
-Direct Test Mode v2.5.0
-nRF54L15 flashed with ncs v2.9.0 direct_test_mode example
There is currently...
Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
Hi!
I'm migrating my development environment to arm-based Mac. I succeed to install nRF Connect for Desktop app for aarch64 architecture, but struggling to get Bluetooth...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
I doubt Nordic developed a brand new GPS receiver for the 9160. Where does it come from (manufacturer and model)?
The Thingy91 Asset Tracker out of the box example has some...
The Thingy:52 Environment Service uses this structure to represent Temperature.:
This is wrong - it cannot correctly represent temperatures below zero but above -1 ...
pls advise if nrf9160 DK can work in RDP protocol , say the board is in US to work on NBIOT carrier or LTEM carrier . Can it be configured in some way to do evaluation remotely...
Hello!
It seems to me that GCC compiler optimization (-O3 -g3) somehow break the SAADC.
When enabling said optimizations the SAADC no longer gives me valid measurements...
Hello,
I'm developing a gateway and i would like to use advertising packet on sensor side to transmit data but it suggests that my gateway will be in permanent scan. I know...
Hi , I would want to establish a GATT Server application as well as integrate Bond Management Service from glucose example (ble_app_gls) in examples folder of SDK15.3.0_59ac345...
ble_db_discovery_start () returns NRF_ERROR_INVALID_PARAM (0x7)
This problem occurs when two peripherals are connected to one central unit. The two peripherals use the same...
Hey,
I am having trouble validating this idea through research. I was hoping someone could give me some ballpark feedback.
The setup:
- 15 NRF52832 devices on custom...
all set. while in linking stage i am getting
.\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol nrf_sdh_is_enabled (referred from nrf_fstorage_sd.o). .\_build\nrf52832_xxaa...
Hi,
I am using NRF51422 dk board in our project.We are using SDK 12.3 version , soft device S130 and keil u vision. Here the problem is I am not able to connect the bluetooth...
Hello:
I am able to debug and output to the J-link RTT Viewer(V6.44e) and when I stop debugging or sometimes randmley, the Viewer will display the message
"Warring:...
We're using SAADC to monitor two different voltage rails in different combinations (sometimes one and sometimes both).
I'm experiencing an issue in the following scenario...
Hi
I followed below tutorial, and I tried to send scan response data
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising...
Hi, everyone,
We are developing projects with nRF52832/51822 chips by using development board PCA10040. The programming of the chips is done by “nRF Connect\Programmer”...
Hi,
I have a problem with the app timer firing incorrectly.
I am using development board nrf52840-DK, Segger Studio 4.22, SDK 15.3.0_59.
When there has gone more than...
