Nordic #Devacademy intermediate course: Ticket for exercise 2 of lesson 2
Dear Colleagues,
I selected the #nRF9151-DK, since it was in the list of recommended boards for...
Hello,
I am developping an application based on PAwR (Periodic Advertsing with response) in coded PHY (S8) extended advertising on SDK 2.7.0.
costum chip nrf52840 (on...
Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hi,
Currently, we develop a prototype that needs to communicate with WuR; the FH101RF. Could you please tell me if it is possible to communicate with it? If not, can you...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
I had setup nRF sniffer with below software and hardware, but the Wireshark seen unable capture BLE data.
• nRF Sniffer software nrf_sniffer_2.0.0-beta-1_51296aa.zip • nRF...
Hi,
I have been working through the examples for DFU with the nrf52832 dev kits from the SDK (nRF5_SDK_15.0.0_a53641a) from this folder:
...\nRF5_SDK_15.0.0_a53641a\examples...
Hi, Guys, I have problem with my nRF51822. I built the ble_app_uart project in the SDK v6 and and flashed it on the mcu using j-link and I also flashed S110 SoftDevice version...
Hi Sirs:
I've searched 52840 specifications and devzone, but there is no related information about the maximum external flash size could be adopted on 52840.
Would you...
I'm attempting to use PPI and Timer2 on the NRF52810 to count the clock pulses coming out of the SPIM driver. As there is no way to do this internally (as far as I know) I...
Hi,
I'm using a nrf52 as pheripheral BLE in embedded system with sensors. I need a ble central to receive the data from the sensors by connecting to the nrf52. I'm trying...
Hello, i am trying to store a lot of informations in the flash in order to do this i separated my data in several arrays. I want to store all my arrays in with the same file_ID...
In our project, two RF modules (with nRF24L01+ IC) are used in communicating data. If there is no WiFi around, the two RF modules can communicate very well without packet...
Hi everyone,
I found this example in the SDK for the nRF52840 Dongle: nRF5_SDK_15.0.0_a53641a\examples\connectivity\ble_connectivity\pca10059\ser_s140_usb_hci.
With this...
Dear Sr.,
Can't detect carrier
They are two PCB one TX Carrier and other mush Detect the carrier ---------------------------------------------------------------------...
mains.c
Hello Everyone,
I have deveLoped the Custom PCB whixh has the push button which is connected to VCC so i would like verify my software logic for button configuration...
Hi,
We have a new product based on the NRF52840. We are trying to add NFC record text to the firmware that based on SDK15. We could get the NFC record text from the NRF52840...
We're evaluating the nrf52840 and I am looking at the SPIM peripheral. The datasheet states the following:
"If several AHB bus masters try to access the same AHB slave at...
i am working on the Cycling Speed and Cadence sensor central configuration using nRF52832 DK in Segger Embedded Studio. I used the RSCS central example of nrf_sdk_v15.0 and...