Hi Nordic：
We are currently testing Zigbee on the nRF54L15 platform using the Zigbee R23-add-on-V1.0.0 SDK. It has been observed that when a low-power node disconnects from...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I have 2x Power Profiler Kit II up and running using the Power Profiler app - started twice and with separate PPK2 instances selected, as described in another support post...
Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
What is the RTC run current on the nRF528120? It is not listed in the datasheet.
In addition, what is the run currents for the clocks on the 810? There is no information...
I need to send data from PC (windows 10) to nrf52832 using UART (hardware) in order to retransmit this data through mesh network with light switch example.
Do i need to...
Because I'm using PTR9618 module of nRF52832, it don't have XTAL 32.768Khz (X2).
When Makefile have NRF52_WITHOUT_SOFTDEVICE=1, hello-world, blink-hello work fine. But when...
Hi,
I'm looking to generate a clock signal on a gpio with an exact frequency. I tried this by setting the pwm base clock and adjusting the top value but got no luck.
Is...
Hi Nordic,
I find somethig wrong while using GPIOTE.
I.
First I call nrf_drv_gpiote_out_init(MY_PIN, &my_config), it works fine. However, I call nrf_drv_gpiote_out_uninit...
dear sir
i had use the ble_ant_app_hrm demo to test ant+ble,but i could not find the softdevice in the folder,so i can't connect it to my mobile phone,the link address is...
Hi, I'm using Central multilink example to connect with our Custom Peripheral sensors. I'm using board PCA10040, nRF52832, SDK_14.2.0, s132. Sensors have a custom service...
For NRF51 and NRF52 antenna matching network, is there any requirements for resitors? Tolerance?
I know there are some requirement for capcitor and inductor types, how...
Hello,
Can we combine a 5-certified hardware circuit with a softdevice that is 4.2-certified? (at examble mbn52832 (module) with s332 (Softdevice))
If yes, with which...
Hello dear
I have a question about NFC on RF52832. On section 42 of datasheet, says:
"The NFCT peripheral (referred to as the 'NFC peripheral' from now on) supports communication...
hello support team,
i have seen thread and sdk14.2.0/examples/peripheral/SAADC example
pca board: PCA10040
can anyone suggest how to read battery status using handler...
Hi,
I am trying to set an nrf52840 pdk (with SDK14 and s140_nrf52840_5.0.0-2.alpha) as peripheral and central at the same time and another nrf52840 pdk just as a peripheral...
Hi,
I play with pca10040 and the light-switch example from SDK for Mesh v1.0.1. Everything works but I wonder why the advertising signals are not seen by nRF-Connect Scan...
