Hello Team,
I have flashed the bap_unicast_server bluetooth sample on my nRF5340 Audio DK. No build or flash errors. When I connect to my phone it connects properly. I'm...
I'm working on a project involving a USB dongle based on the nRF52840 SDK-2.9.1, which needs to communicate with a sensor (also an nRF52840) and transmit data via USB to PC...
Hello Nordic team, For the ( POC), I configured ADC channel 1 and interfaced a potentiometer to pin P1.14. The ADC was set up accordingly to read raw value from the potentiometer...
Hello, I have been going through the DFU and FOTA lesson in the Nordic intermediate course. I see that there is a FOTA support for a scenario in which we want to update a...
Hi
I need to sync a PC with a BLE board. Fixed delay is not a problem, but jitter should be max +/- 1 ms.
Our competitors have solved this issue some how.
As we all...
Hello. Right now, I am connecting an external flash using SPI. The external flash is used for firmware updates. I'm trying to launch sQSPI to access the external flash. I...
I just received my new NRF52480 PDK, but it will not respond to any commands.
I tried nrfjprog -e -f nrf52 and this is the log output:
-----------------------------...
Working with nRF52832 and SD132-v2.0.1
Using external 32.768kHz xtal in addition to 32MHz xtal.
I realize there are a lot of posts about timers, but I didn't find any...
I'm having difficulties writing, retrieving and deleting data from flash, using fds on nRF52832_XXAA. Sometimes the flash writing succeeds, sometimes it fails with with ret_code_t...
I want to know about some range information of the NRF52 & NRF21 (BEACON).
For example if I have TX power of the beacon +4 dBm and which is broadcasting every 500 ms so...
Hi all,
I tried to build the latest OpenThread libraries but after copying the library files in the SDK, I fail to compile the examples. Everything was fine when building...
Hello,
the specification states that SD132 v4 takes 120 KB flash and MBR 4 KB flash additionally. We only need the BLE protocol stack. Is there any way to reduce the SD132...
I am trying to use the EVENTS_PWMPERIODEND interrupt to read a GPIO pin on every falling edge of an output GPIO that is driven from the PWM module.
The description in the...
Hi all,
i developer a code that :
press button short switch on one led
Press button long switch on two led.
but sometimes if i press the button a two led...
hi
i need store my data in internal flash memory (around 30kb). i have fixed memory map from 0x25000 to 0x35000. my,
block size = 16 byte,
block count =4096,
no of pages...
Hi,
I want to add functions of HID telephony to pickup/decline phone on nrf51822 application.
But it seems telephony usage did not work on android/ios phone, or incorrect...
hi :
I use Gzll protocol to realize 2.4G frequency hopping communication， One Device send data to One Host on Pipe2 receive. Now I use nrf24lu as "Host" and nrf51822 as ...
Hello,
My rigado BMD 200 board suddenly stopped responding. the Jlink interface cannot connect
I tried nrfjprog --recover with no success.(says cannot connect)
in segger...
I am using nrf51822 with sdk 6. I was using double bank ble dfu for the firmware upgrade. But now I have to switch to single bank dfu since my code size has exceeded the maximum...
hi ，
image 1 、
image 2、
image 3、
I now use nRF24LU1P for Bootloader upgrade, using the routine is the official website of the C# Lu1BootLdrTest project, nRF24LU1P...
Hi,
I have a nrf24lu1p usb dongle by hand and I want to know the flash size.The package marking is:
nRF D
LU1P16
1219AC
I am not sure whether the chip has a 16kB flash...
