I thought this should be very simple but it has not turned out that way. I have started with the pc-ble-driver heart rate monitor (peripheral) example. I was able to take...
Hi,
I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central.
The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
Dears.
when I connect nRF52833 to connect DK board, JLINK is ok .but could not find device from target device selection.
nRFGo studio is the same. what's the reason for...
Hi All,
I am able to perform the OTA DFU from the NRF52840 Dongle using the NRF Connect Bluetooth low energy application and default Nordic firmware.
I would like to...
I have a service with 2 characteristics, TX and RX. On TX the notify is enabled, because TX should send a notification when something changes. I manage to change what is needed...
Hello everyone.
We have a design based on NRF52840, which uses the built in USB peripheral and was fully tested and prototyped using NRF52840-QIAAD0-2031MR. We have now...
Hi There,
I have downloaded the nRFgo studio and nRFgo SDK and other files found here: https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF24-series
...
For the MPSL/timeslot example in NCS 1.5.0, I am trying set up a TIMER0 compare interrupt to take clean-up actions before the timeslot ends, as suggested in here . However...
Describe the bug Attempted to use the samples/bluetooth/hci_usb/ project with CONFIG_BT_EXT_ADV=y CONFIG_BT_EXT_ADV_LEGACY_SUPPORT=y CONFIG_BT_EXT_ADV_MAX_ADV_SET=4 CONFIG_BT_PER_ADV...
Hi, I have the Power Profiler Kit PCA63511 used on top of the dev kit PCA10040. I am trying to measure the power consumption of my custom hardware implementing nrf52832 using...
I'm already using nrf51 in a project and now I need to make a DFU with BLE using a gateway. For the gateway project, I was thinking of using a nrf5x to implement a DFU master...
Hi , a day ago i recived my first dev board from nordic semiconductors, the nRF5340 . Until now I only coded for AtMega328 , esp32, esp8266 and other microcontrollers like...
I am trying to build the aws_fota example project for the nRF9160 using the nRF Connect SDK and the Segger IDE. We currently have v1.5.0 downloaded. The project is not compiling...
Hello everybody,
i use two nrd52 dk boards with nrf mesh light server flashed on them (mesh sdk 4.2.0)
They are configured over nrf mesh app to be in the same network...
Hi, I have nRF52840 DK. How can set the max range? or how can increase/decrease the tx range? Also is there any range extender to improve range? Thanks!
Hi,
I am currently doing a uart dfu over 2 nrf 52840 dks on a Windows PC. I have been using the example found in ...\examples\dfu\secure_bootloader\pca10056_uart_debug supplied...
