I thought this should be very simple but it has not turned out that way. I have started with the pc-ble-driver heart rate monitor (peripheral) example. I was able to take...
Hi,
I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central.
The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
Hello, I've spend some time updating our nrf5340 application to NCS v2.7.0, including using the new hardware model and using sysbuild. We have a custom application that we...
Hi,
With zephyr's example : https://github.com/zephyrproject-rtos/example-application I am evaluating to add a sample clap sensor as a custom sensor into the zephyr sensor...
I was working with nRF Connect for Desktop version v4.1.1 for quiet some time and it was working good, Since each time I was prompted to update the software to the latest...
Hi, I am using a NCS v2.6.0.I created a custom zephyr project. Implemented custom ble service and added BLE DIS and BAS services from source. 3 out of 2 services working properly...
Hello.
I wanna develop customized bootloader using C.
There's two purpose for this.
1) Select application area : Slot 1 for main application and Slot 2 for new...
Hi,
Does the nRF52832 support the Connected Isochronous Streams (CIS) / Channels and Connected Isochronous Groups (CIG), either using nRF5 SDK or nRF Connect SDK?
I would...
Hi,
I am using direction_finding_connectionless_tx/rx sample, and NCS v2.6.1 for AoA. I made some modification on the rx side to stream I/Q data via serial port, and read...
Hello,
I am running into a problem with my Thingy:53 device where I am unable to load up the bootloader. I has the edge inpulse application working well yesterday, after...
Hello,
I have the nRF54L15 PDK and am experimenting with the intermediate tutorials for the Zephyr RTOS. I am working on Lesson 1 - Exercise 1 ( https://academy.nordicsemi...
nRF Connect 5.0 crashes after asking to install nrf-device-lib-driver-installer.exe and shows the following cryptic message.
Trying with nrfconnect-setup-4.4.1-x64 raises...
Hi,
We have a nRF5340-DK board with the following setup:
b0 as the first stage immutable bootloader
MCUBoot as the second stage upgradable bootloader, which needs...
Hello, I have an issue with a project I'm working on with a nRF5340 Audio dev kit. I am using VSCode with the nRF Connect SDK plugin, and SDK version 2.6.1.
I need to have...
Hi,
We are working on nRF5340 with TF-M enabled and iOS application.
What we are observing is the peripheral device MTU TX and RX are configured to 512 bytes whereas the...
Hi I'm using nRF7002-DK kit and I noticed that the output voltage of a GPIO is 1.8 V instead of a 3.3 V. I have encountered a solution mentioned that we should apply these...
I’m working on an nRF52832-based project using the Nordic SDK (v3.5.99-ncs1-1) and MCUboot for OTA updates. I have a 512KB internal flash and 4MB external SPI flash (P25Q32H...
