The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
The peripheral application I'm working on implements a service which must handle multi-byte incoming messages from a central device and would welcome a pointer to any example...
Hello
I found a possible bug in NCS 1.7.0 which was introduced in PR #5353 .
1) False UNKNOWN event when disconnecting
The "invalid cell id" check leads to an false...
Hey
I'm using the softdevice s140 in my project (and the latest SDK 17.x).
I successfully enable the softdevice and am able to start an advertising (as peripheral). However...
Hi
The baseline current consumption running the azure_iot_hub is very high.
I'm using nRF Connect SDKv1.6.1. The sample connects and sends data to azure as expected. But...
Figure 4: Memory layout
Shows code RAM beginning at 0x0080 0000 but nRF52832 Engineering A Errata 33
"Code RAM is located at address 0x0800_0000".
Additionally 0x2100...
Hi,
I am developing a product based on nrf52840 soc as a central Bluetooth device. I want to connect to a Bluetooth device (as a slave) while it is advertising, but unfortunately...
Hello everyone, i'm trying to run the button sample with Pull_up on the pin P0.27 i did the wiring like below
power->VDD nrf-HV
GPIO->P0.27
i attached a resistance between...
Hi,
Does nRF5340 require any calibration in production line in terms of below items. If so could you share any documents on them
- Gain for the RF front end
- Crystal...
Hi, helpies
I am currently workibg on nrf52832 board and now there are some changes in the hardware and we are left with pin shortage,so we planned to upgrade to nrf52840...
Hi, I am implementing NUS which is based on example BLE_NUS & BLE_NUS_C. The connection is not 1-to-1 but 1-to-7. i.e. 1 Central connects to 7 Peripherals. Although ultimate...
I tried following the " Bluetooth low energy Services, a beginner's tutorial ", I ended up getting stuff to compile and run by making a copy of the ble_app_hrs example, and...
Can I write a J-link flash algorithm by myself? Is there any open source Flash download algorithm for reference? When I call west Flash --recover, I can skip the 4K flash...
Hi,
I am developing a product based on nrf52840 soc as a central bluetooth device. i want to connect nad pair to a bluetooth device (as slave) while it is advertising. ...
Hi,
I am developing using the SoftDevice s140 7.2.0.
I am trying to use the MBR function sd_mbr_command() to upgrade my bootloader with command SD_MBR_COMMAND_COPY_BL...
