Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello Devzone Community,
To compile nRF Zephyr based applications at the command line normally depends on the meta-tool `west`. `West` has many capabilities and options...
Hey all Trying to understand how to properly build a basic bluetooth example without errors using zephyr between the 2 cores Error: manually cleaning and flashing reading...
Hello,
I use this code for system_off on a nrf52840 custom board. const struct device *button = device_get_binding("GPIO_0"); gpio_pin_interrupt_configure(button, SW0_GPIO_PIN...
nRF52840 Dongle is configured as Sniffer in the right way according to documentation. When sniffing capture on Wireshark is started, only the Advertising packets are captured...
I have a project where I use the nrf9160dk as a gateway between a BLE sensor and LTE.
The hci_lpuart sample is flashed tonrf9160dk_nrf52840 and the nrf9160dk_nrf9160_ns...
I got a Segger J-Link EDU to be use to program my Nordic Thingy 91. I have previously program the device via USB using the NRF Connect Desktop :Programmer. But connecting...
Hello everyone,
I am having an odd problem. I am using an SoC based on the nRF52832 (the ISP1507-AX). I am using ncs v1.7.0 for development. I am trying out a few things...
Hello guys,
I would like to work using nRF52 as my processor to create products in the future, but I heard about Specific Absorption Rate (SAR) testing and that is good...
Hi all, I am a little confused by the requirements for the external GPS antennal options. My board is version 1.0.1.
In this page ( https://devzone.nordicsemi.com/nordic...
The project I'm using the peripheral BLE UART that has been modified to use freeRTOS and PWM.
I'm using two channel PWM to drive a resonance motor at 25.6 kHz. If I disable...
Dear
First of all, I am so sorry because of my english skill.
I got NRF_ERROR_RESOURCES when the connection between NRF Module and mobile device is disconnected due to...
I want to start the most basic hello world project on my nrf9160 thingy development board but am having trouble building my own custom project or any of the sample ones provided...
Question on an older chip:
Can anyone tell me if FW originally written for the nRF24LE1E would be completely compatible with the nRF24LE1G? I have an opportunity to source...
