I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hi,
On our NRF52840 Based product, we have enabled USB CDC Use.
We see increase of ~0.5 mA when enabling USB . We are ok with this , However - when we remove the USB cable...
Hello Nordic Team,
I am creating Scanning application using SES for NRF82532 (SDK 15.3.0 and softDevice 6.1.1), i am using app_timer_freertos timer.
application is calling...
Based on Android studio 3.0, gradle-4.10.1 compile the project downloaded from github.com/.../android-nrf-mesh-library . I get the following error:
The module 'app' is an...
Hi,
I have an external flash ( via QSPI ) working on NRF52840 Based product.
I'd like to redirect all NRF_LOG message to a file , is there a similar log backend available...
Dear developers,
My device uses the NRF52840 SoC and is equipped with a modem for internet access.
To perform firmware upgrade, I imagine I would have to download a DFU...
Hello, I tried to work with nRF52832 to read adxl362 registers, Here is my function to read all 3 received bytes from adxl362 (according to datasheets, the last byte must...
Hi,
I tried to install the latest sniffer v3.0.0 and Wireshark v3.2.0 on my computer. I could not see PCA10056 listed. If I start my wireshark from command line, with "open...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). My goal is to send data from sensor over bluetooth...
When i used Port 0 assigned on Uarte rx tx pin , everything was ok.
But when i changed the rx tx pin to port 1 , for example p1.00,p1.08.p1.09, it doznt work...
i am sure...
I use nrf5_SDK_for_Mesh_v3.2.0_src , nRF5_SDK_15.3.0_59ac345 and board pca10040.
Copy the ble_app_uart_coexist folder into the examples/ble_peripheral folder at your nRF5...
Hello.
I'm doing a DFU customization now.
However, because of the problem of data transmission of the last packet of the first page when advertising,
connection and...
I am setting up a relatively complex project that runs on top of FreeRTOS and it is based on the HRS freertos sample app from SDK 16.0.0. The device will need to run in several...
Hello,
I am trying to setup a PAN coordinator by following these steps:
1. mlme_reset_req() -> successfully responds with a mlme_reset_conf_t by calling the callback...
