Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello,
I'm experiencing issues testing the FOTA over BLE on nrf54L15dk using the SMP server sample of the NCS v2.8.0.
To reproduce my issue, just build the sample out...
Sorry if this is documented somewhere, but there is a dot pattern that seems like a QR code on the 9160's exterior metal case. For the purposes of provisioning a product,...
I performed OTA over BLE for Matter samples available in NCS. After OTA performed successfully, it erased the Matter commissioning data and uncommissioning the device. How...
Hello!
I am working on a project based on NRF52832 MCU and NRC connect SDK in VS Code.
I have a custom PCB and I use GPIO pins to switch on the power of the OLED display...
Hello, I am studying DevAcademy Lesson 4 - Data exchange in Bluetooth LE , specifically Exercise 3 using the nRF5340DK . While attempting to build the corresponding Git code...
Hello,
We have a project which requires high accuracy for 14-bit resolution ADC output by using Nordic nrf52832, we regard that the accuracy is linked to the internal...
Hello,
I'm using nrf5340 audio application in nRF Connect SDK v2.7.0.
It has been working normally, but today when I opened folder, the sidebar disappeared, as shown in...
Hello everyone,
I guess my question is more conceptual rather than a specific issue with the code.
I am working on a device featuring an nRF5340 chip and an nRF9160 chip...
Hello, I am trying to get a custom board with an nRF5340 (on a Raytac module) up and running. I want to emulate a simple HID mouse. Therefore, I selected the code from the...
I have just started using 2.7.0 with the nrf54L15 chips and come across a few problems.
When trying to run the UART sample I found that the app overlay files, which I believe...
Other than setting the DCDC_MODE_PIN, what else does the sd_power_dcdc_mode_set() do?
I'm seeing an issue where I have a GPS peripheral on UART that is seeing about 10dB...
Hi Nordic team,
Hi Nordic Team,
We are trying to configure two SPI masters. It works when I use any single SPI (only one), but when I add the second SPI, I encounter...
Hi,
I am trying to compile an old project.
I am using SEGGER_Embedded_Studio_Nordic_v568_win_x64 with nRF5_SDK_17.0.2
I am getting an error message for the following...
Does the 7002 support 802.11 monitor mode? https://en.wikipedia.org/wiki/Monitor_mode
Some chips call it promiscuous mode even though that should be something separate ...
