Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi Support Team,
I am encountering various problems with the Developer Academy example found here:
https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals...
Hello,
I am using NCS v2.8.0.
In this, when I configured the application to use OOB legacy pairing only mode, the build process failed.
Following is the configuration...
In our firmware we use BLE together with ESB using the MPSL timeslot API, with the implementation inspired by this example: https://github.com/too1/ncs-esb-ble-mpsl-demo However...
Hi,
I am trying the sample code in this regard. I have changed the I2C pins in the overllay file and bme register address to 0x77 as follows. It seems working but I have...
I am using nRF52840/nRF52833 (raytac module, original board). With the current nRF Connect SDK, is it possible to disable NFC and use ports (P0.09, P0.10) as GPIO?
I am...
Hello,
we are currently in the process of verifying the nRF LwM2M Client, specifically focusing on the Queue Mode functionality. During our testing, we encountered an issue...
Hello,
I am facing issue while initialising seed by calling "mbedtls_ctr_drbg_seed" function I am getting -0x34 error and when I analysis this I got to know that I have...
Hello,
It has been a while since I have done any controlled impedance and was wondering if someone could provide me a quick sanity check before I continue:
Here is the...
Hi,
Does nRF52840 support stable modulation Characteristics
It is found that Stable Modulation Characteristics fail during the test, and the capacitor of the debugger...
Hello everyone,
I'm using nRF52832 with SDK v17 (S132 Softdevice).
I don't know why, but I can't disable softdevice. I can enable it normally, but when i make use of...
Hi,
I’m looking to monitor LTE-M or NB-IoT packets sent by the Thingy:91 in real-time using an app or software. Currently, I’m using the Thingy:91 to send temperature logs...
Dear devzone,
I followed this instruction to use nRF54L15-PDK v0.8.1 to burn external boards. The wiring diagram is as follows:
Command line input: nrfutil device recover...
I have a Minew MSR01-B milimeter wave sensor and I would like to know if there is any nordic hardware that i could use to comunicate with MSR01-B sensor, get the data and...
Hello,
I am designing a battery monitoring circuit for a 3.0V CR2032 coin cell using the nRF52840, and had some questions. I am following the battery monitoring circuit...
