I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Previously, nRF Connect SDK was working without issue. However, now when I try to create a new build configuration, it hangs at the following step:
It's unclear why this...
The instructions are: On the command line, open the directory ncs . The following steps have one do a west init directly in the directory ncs. But they should say to create...
i used sdk version 15.2 everything work fine but in ios 15 its not show services when android work fine and ios 14.8.1 also work fine and show services please help
There are multiple errors:
Failed to clone the repositories: Error: Cloning into '~/ncs/v2.6.1/.west/manifest-tmp'... /~/ncs/toolchains/2be090971e/usr/local/libexec...
When initially starting Sidewalk on BLE it seems that the current consumption is high if you start with only LINK1 enabled. It seems that perhaps this is due to the SX1262...
I am using Wireshark 4.4.0 and Nordic nRF Sniffer for Bluetooth LE 4.1.1 (nRF52840-Dongle PCA10059). In Wireshark I see a device, a peripheral, sending advertising packets...
hey, I am using nrf52840 in that i am making it compatible with DFU by using sdk2.8, but getting this error
C:/ncs/v2.8.0/nrf/include/flash_map_pm.h:47:22: error: 'PM_mcuboot_secondary_ID...
hello!
I am currently using the nRF7002DK to implement the examples from nRF dev academi. I am practicing based on lesson 5-exercise 2.
lesson 5 exercise 2
In the example...
Hello, I want to make my project DFU OTA compatible, so when I tested on development it works fine once I created my pcb using nrf52840 module in it. So it is taking huge...
Hello,
I have a question regarding a recent issue.
I'm currently developing with the nRF52840 IC or EVM, and I'm facing a problem. Whenever I write firmware to the flash...
Hi Team,
I recently purchased 2 Audio DK's and I set one up as a gateway and the second as a left headset. I was able to pair the two, stream audio from my PC through the...
Hi,
We are currently developing a BLE device (HW and SW) using the NRF52811.
As we want to be able to update the device via FOTA we need to have the Bootloader to have...
Hello,
I am trying to upgrade my project from ncs 2.1.0 to ncs 2.6.1. I am running into some strange issues with mbedtls and I suspect it's because the same ciphers enabled...
Hi All,
We're going through BQB certificate with our mice, and we're informed that test get failed because new rule will be implemented in May 2023.
Our Chip is NRF52833...
