I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hi,
I have a question about 'Thread Secrue DFU',according to the ' https://infocenter.nordicsemi.com/index.jsp ' ,the 'Thread Secrue DFU' does not use softdevice of transform...
Greetings,
CPU = nRF5340
SDK = nRF Connect SDK v1.6.1 and 1.6.0
Board = custom
For the nRF5430, we have a custom board that uses active high logic to turn LEDs on...
Hello,
I am trying to get the nvs driver working on the NET cpu and am having trouble getting the initialization working. The code below is what I am currently working with...
There have been several other posts on this issue dating back a few years, such as this one .
On Windows 10, if I am using SEGGER's RTT Viewer and I flash a nRF52832 with...
Dear,
As the example code is shown, I have been implementing on LED PWM through nRF53 GPIO0 12. If I set the brightness to 100, it was ON without any issue. However, if...
I use the "zb_sleep_now()" function in the main loop, which greatly reduces the start current. The device wakes up apparently due to the RTC2 interrupt used by the zigbee...
I want to use ncs to get the RSSI at 10ms intervals.
For example, central receives an empty packet from peripheral at 10ms interval.
I would like to know if there is a...
Is it possible to set up an NRF Connect SDK project such that the firmware can be updated over BLE, without including the SoftDevice in the update?
I'm using NRF52810 which...
Hello,
i have searched for uart, i2c/twi communication with polling, interrupt, DMA method different brief explained guide for NRF52
but i have not found it any where...
Hello,
Previously, my nRF52840 DK worked perfectly fine through the USB (J2) connector. Then I successfully programmed PCA10059 by Debug OUT(P19) of the nRF52840 DK board...
My Android app allows the user to un-provision a mesh node. To do so, the app just sends a ConfigNodeReset message to the node's unicast address, which works perfectly if...
Hi, I want to add some auto-test capability to my nRF5340-based project. I thought one useful feature would be to measure voltage AND current at the hot node when all devices...
Hi all
We are switching to nrf-sdk v1.6.0 in our project and encountered a problem with MCUBoot.
The image builds successfully and can be flashed successfully as well...
