The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hello
We are planning to build a product based on nrf52840 our programming part is almost done we used nrf52840Dk board , now we are order SoCs and other peripherals ...
May I know what is the difference of three PNs NRF51822-QFAA-R (H0) AND NRF51822-QFAA-R (G0) AND NRF51822-QFAA-R?
How to identy the three PNs? May I know if NRF51822-QFAA...
I am trying to implement a scenario where the system will be sleeping for a mentioned period of time and then wake up and advertise and transfer data over BLE.
I am using...
Again, if the search engine in your documentation were decent, I would probably not need to ask this question here. The answer probably exists, but try an find it not knowing...
Hello Nordic lovers,
Happy Merry Christmas.
In ble_uart code, I'm interfacing the FreeRTOS & twi_sensor code
The program executed without any error.
And it starts...
Dear Members,
How can I wake up the chip without a button
I'm using the example for Ant,
Ant_bsc_rx .
I have disabled the button with :
bsp_init(BSP_INIT_LEDS...
Hello and Merry Christmas,
Trying to get Thingy:91 connected to cloud. But no such luck.
Followed the video, but somethings are shown. Installed latest firmware (SIP modem...
Hello
I have two questions. Your thoughtful response will be appreciated.
1) What's the impact on power consumption with 1 Mbps vs 500 kbps vs 125 kbps for the same amount...
Is there any way to leave the PPK 2 output enabled when I leave the Power Profiler app? If not, then can I submit this as a feature request?
Without this option I have to...
1、Does Nordic 5340 support 1443a protocol；
2、When the chip（5340） is not powered, does NFC function support passive swiping card
3、Can the reading distance of NFC be more...
Hello
I am using the APII described here:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/include/modem/modem_key_mgmt.html
to add keys to the modem...
Why does the nRF9160 Tx power fall far short of the specification? Its seem to be a false claim that the nRF9160 is a 23 dBm device, and rather is a 20 dBm device. In other...
In the flash write example code the very start of main.c has the following lines
The comment says "Use last page in flash". However, what I am guessing from the code itself...
I am trying to use nrf_serial with IRQ. Tx operations just fine but, i can not get any interrupt when a data comes from uart. I am using sdk 14.2 and not using ble.
