Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Out of 10 prototype boards, we have 3 not working well due to 32 KHz xtal issue.
7 units are OK, but the other 3 units works only when configured with internal RC osc. ...
Hi,
I have been hired to migrate an NRF51 project that has S310 to an NRF52 one on S332.
I have looked at the migration guide in detail and had some follow up questions...
Hi I am having a hard time implementing DFU using SDK12.3 / nRF52832 now. I have tried so many times, but have failed a lot and have left a log similar to the next one in...
Hi,
I am using v0.4.0 ncs sdk.
I added following in the nrf9160_pca10090ns.overlay file
I added following in the prj.conf file
I added following in the...
I made a Windows application that makes USB connection with nRF52840. You need nordic_cdc_acm driver to use it with windows 7. Can I distribute the nordic_cdc_acm driver with...
Is it possible to route a signal derived from internal clock to an IO pin? I am new to NRF micro controller. My experience has been with Cypress PSOC and in the IDE it was...
I am trying to implement a struct that will be saved in non-volatile memory. Does the dev kit have these capabilities on its own? If it does is there a guide on how to use...
Hello,
I am using secure dfu with bonds (SDKv15.3, Segger, nrF52832), it works fine however after each dfu (application only) I lose the bond information.
I have search...
I am trying to communicate with PN7150 from nRF52840 DK using I2C pins.
PN7150 needs 3.3V and nRF52840 is supplying 2.9V.
I am able to read PN7150 on Arduino Mega but...
I made a Windows application that makes USB connection with nRF52840. You need the nordic_cdc_acm driver to use it with windows7. May I distribute the nordic_cdc_acm driver...
Hi Nordic,
We're developing a product based on the nRF52810 and got the following question:
We were wondering if we can recover a board in the worst-case scenario where...
Dear all, My team want to develop a innovative product. I am following this tutorial ( www.youtube.com/watch to enable the CMSIS Configuration Wizard in Segger Embedded Studio...
I am working with SDK15.3.0 and a PCA10040 with S132. I have two questions relating to the BLE addresses as seen by the PCA10040 and by nRF Connect.
Q1 - What is the relationship...
Modem firmware version 1.0.0
Segger version v4.18
nrf tag v1.0.0
Often when I try to flash a new build of an application and try to flash an application through Targert...
