I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
Hi,
I am using nrf mesh sdk v3.2.0 and I would like to combine our custom service within the mesh server example (includes the proxy service). Using info from other threads...
We are having issues with UART communication on the nRF52840. Using a logic analyzer, we have found that the transitions happen too quickly. This causes the receiving MCU...
I have been working with Thingy:91 for three weeks now. Everything works nicely, however, I could not get any GPS location from it. I am using Rogers simcard which is a local...
Hello everyone. My project is getting quite complex so I will try to abridge. (Mesh SDK 3.2.0) I am trying to send wifi credentials from an android application (derived from...
Hi guys,
here in Croatia I'm trying to connect to NB-IOT network using nrf9160.
Here are the commands i am executing:
After this command modem does not accept any...
hi all,
i build project use HCI controller with nrf52840 , it some time show error message,
how to deal with this issue
HCI Host Not enough space in buffer #hci
https...
Hi,
I am working on a development where the values of a bunch of nodes with a sensor needs to be captured in one aggregator device in a mesh network. The aggregator then...
I tested ble_app_att_mtu_throughput_test code with 52840 EVB for BLE5 Long Range as below site.
( https://devzone.nordicsemi.com/b/blog/posts/testing-long-range-coded-phy...
Hi everyone,
I am trying to use the Port interrupts on the nRF52840. I started from the example "pin-change-int" and it works fine when I use one input pin.
But when I...
Hi,
We have a product composes of a central and a peripheral which uses Nrf52840 as their MCU and communicate with each other via BLE. The peripheral will send some data...
Hi,
what should I do in order to enable Bluetooth Low Energy on PC (mainly Windows XP to 8, but Linux or Mac would be nice if they don't support BLE natively)?
My device...
Last few lines of log
After looking into error code it shows 'DFU_END_ERROR_UNAUTHORIZED'. I followed procedure from here . Am I missing something here. Have flashed my...
how can i do a new characteristic ( all new 128bit-uuid )Under the same service
this is i try use nrf connect to do this , i hop add new different from NUS servic ( only...
I received the device and tried running the default asset tracker that was installed and kept getting these messages:
DEBUG modem << Connected to LTE network\x0D\x0A
DEBUG...
