If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
After downloading nRF5 SDK v17.0.2, I checked the Release Notes - and they state SES v4.50 has "been used for testing".
So I downloaded & installed SES v4.50
The HID Keyboard...
Hi, recently I want to establish a connection between two development boards (STM32F103 + nRF52840-DK), that the STM32f103 board can create the data and send it to the nRF52840...
Hello, I have a project running on a PCA10040 board, using softdevice 132 (0x9D, v5.0), ble and serial port for data transfer.
I want to migrate this project from this...
I am trying to use the UART for a custom version of the DFU. I have it transmitting no problem, but I never get the RX_DONE event. I cannot see any reason and I have looked...
Hello,
I have a question because there is a problem with writing code using timer.
I wrote the following code to avoid using the LED timer when I first ran it.
However...
Hello Please help. I want to connect ble central to a specific address. And the ble peripheral has a ble central address, that can connect to it. 1. Is a whitelist used on...
hi,all
i am a new learner about the BLE
when i use softdevice 17.0.2 to run the example (anyone) ,there is no problem.
then I want to use the SDK12.3.0 to run a formal...
hi
I am using nRF52832 and mesh sdk V4.2
I have modified the light switch example in order to send 1 byte of data instead of the on-off commands. in the server side I...
Hi,
I have a problem with coap response. I use iot coap library.
Client send nonconfirmable coap message with payload to broadcast addr
Server get payload and send nonconfirmable...
I am getting the Following error after connecting the JLink
I followed the following procedure
What am I doing wrong? DO I need to install anything else?
Hey All,
I ran into an issue on the nRF Connect SDK trying to get a nRF52840 advertising using CODED PHY. I figure it's not fully implemented yet are there any updates on...
I advertise as
BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE
BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED
This posts suggests I may have not really disabled...
I am using an NRF53 DK board with nRFConnect/Zephyr 1.3.0. I need to define the UART pins I will use in a .overlay file but I would like to NOT define any flow control pins...
Hey
I am working on nRF51822 SDK12, S130
I have encountered a problem when connecting and disconnecting from the device at a fast rate, occasionally comes an event in...
Hello,
We integrated latest released version of "pc-ble-driver.py" & "nrfutil" in our custom linux os running on ARM 32bit based custom board (B1).
pc_ble_driver_py :...
