hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
i want to connect my nfr51822 device to only one phone( that means which phone was connected first). For this purpose i enable whitelists but i create whitelists nothing has...
In timer example in sdk 11, I replace the Timer 0 by timer 1 and timer 2 but the LED did not blink. Can you guys please guide me through this? In nrf_drv_config.h I have already...
I have Keil uVision-5 and loaded the legacy patch. However Nordic NRF51 does not appear anywhere as an option. The Project loads fine and compiles. However, I cannot use the...
nRF52862, SDK 14.2, SD 5.1.0,, Arm GCC (Eclipse)
I have a custom service that is working well when 1 device (phone) is connected. All notifications are sent properly to...
Hello everyone,
I am trying to add new service into ble_app_uart example. I compile successfully. I do not get an error. But the device is not advertising. I can only advertise...
In my plan, I have used NRF52832 IC as the transmitter and the NRF24LU1P+ as the receiver. I have tested the wireless transmission successfully. In order to reduce consts...
Hello,
I get the sources from Thingy Mesh Demo and use the guide to build it examples. Thingy_node build without errors, but Thingy_bridge return the error "too few arguments...
Hi
I am using nrf52832 doing a project and I 'm new to this MCU.
My project concerns sending data from APP via BLE to nrf52832 to config parameters of SPI (data and clock...
Hi,
I am trying to modify the multilink central example to send string to other board (peripheral)
I already did the UART configuration and in my tests I saw that when...
Hi, I tried the above tools(nrfjprog) on the Raspberry Pi 3.
But, I saw the error shown below.
pi@raspberrypi:~$ ls | grep nRF5x
nRF5x-Command-Line-Tools_8_5_0_Linux...
We are trying to modify the nRF Beacon example app for iOS that Nordic provides. We are unable to get app to see the devices from the iBeacon kit when they can be seen from...
The manuals for the nRF51 and nRF52 list the maximum ESB radio channel number
as 100, but in the SDK the guard value in the set channel function is <= 125
(in both the...
I am about to start development on a project that will be using a pair of nRF52832's to make a low data rate connection between a PC (with a nRF52832 based dongle) and a device...
In the event that a Nordic soft device library call fails (as determined by APP_ERROR_CHECK() macro) and our application level app_error_fault_handler () function is called...
