Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
I need to send an audio signal through BLE connection of nRF51822 module, this signal need to quantized and sampled at rate of minimum 8000 sample/second by ADC, i...
I would like a working example of a simple application that uses soft_device (either S110 or S120) plus UART debugging.
I have read many posts in this forum about this topic...
Hi folks,
do you supply a BT Test-SW to set a module with your NRF51822 in different test modes like continuous FH etc. or to change the device to low, mid, high channel...
Hi,
I want to establish a peer-to-peer communication network between 2 nRF51422, such that both the nRF51422 can Transmit as well as Receive data. Is it possible to achieve...
hi,
as we know, the device need to being linked in 1.28s if Advertising types is BLE_GAP_ADV_TYPE_ADV_DIRECT_IND ,but my host can't link device in 1.28s,so i want to link...
Hi,
I try to evaluate DFU using serial but found difficulty. Seeking help here.
I use PCA10028. First, i falsh S110, v8.0 into it.
Then, compile SDK8.0.0\examples...
Hi all!
I want to allow only 1 device to bond at a time. If another device bonding, I want to delete the previously bonded one.
I tried to use dm_device_delete_all() in...
Hi all,
I'm trying to get TWI working on the nRF51 DK but it's not working.
I used the twi_hw_master_sd.c file so softdevice use should not be a problem.
When I debug...
I am using internal ADC to sample 2 (sometimes 3) channels on about 333Hz frequency.
What I do is:
set channel 1 as input (always two-thirds prescaling, VBG reference...
Hi,
I want to debug nrf51822 beacon using DK.I made the necessary connections between dk and beacon.I managed to flash the beacon using nrfgoStudio , but if I want to do...
I have the following code, it's pretty bare in terms of its functionality:
#include <stdint.h>
extern "C"
{
#include "nrf_delay.h"
}
#include "gazell.h"
#include...
I succeeded to made the BLE DFU example of SDK 8(bootloader\pca10028\dual_bank_ble_s110) with softDevice 8 working on PCA10001.
Now I want to try DFU over UART.
I follow...
Hi,
Sorry if these are silly questions but I've tried some searchings and still cannot figure out the answers for the questions below
What is GATT Server Context...
Hi,
I wrote some code that writes to the flash perfectly when BLE is not enabled but when it is enabled, some of the data are correct while others are either missing or...
