I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
hi..
i merged the two programs twi sensor and uart ... successfully complied
but while debugging i am getting this error
while (m_xfer_done == false)
lm75_mode();...
Hello all,
I have a question about the SAADC of nRF52832.
Now I use the SAADC to measure the some external sensor voltage and the internal VDD voltage.
The sensor connection...
Hello, Excuse me! I used the LFRC,the calibration interval of which is 8s, in my application on NRF52832. In order to measure the power consumption,I want to know the duartion...
Hi,
As well know, nRF52832 can use "16Mhz base-clock to output PWM signal, and it is very simple to create 4Mhz, 2Mhz, 1MHz signal output,
But, If I want to output a...
I'm trying to get a stripped down, simple LED blinking sample to work (like blinky) when building with GCC however main() is never called. I'm guessing I'm either using the...
I'm trying to take a project we had working with only an application, no softdevice or bootloader, and add a bootloader and softdevice, with the application still not requiring...
I am working on nrf5_SDK_for_Mesh_v2.2.0 with nRF5_SDK_15.0.0 and softdevice 6.0.0. I run code on PCA10040 dev boards. I am trying use a timer to send onoff message from a...
Hi Nordic,
Does FDS affect PPI ADC acquisition when writing data? The test found that once the FDS is written to the data, the ADC data returned by the PPI ADC is fixed...
Hello Nordic experts,
I am working with nRF5_SDK_15.2.0_9412b96 SDK.
In example nRF5_SDK_15.2.0_9412b96/examples/ble_peripheral/ble_app_hrs_freertos/main.c I have at line...
Hi all,
The setup that I am aiming for has a number of nodes, which will send the IMU data to a central base station. The communication is achieved using a bunch of nRF24L01...
I keep getting stuck in the TIMER1_IRQHandler function.
When I debug the code, I get to line 20 (exiting interrupt function scope) and then the assembly code hits a nop...
Hello!
I have developed a BLE HID (HOGP) device in Nordic SDK 15.0.0 starting from an example project: ble_app_hids_keyboard .
The HID device that I have developed however...
We have a setup where we want to measure the current consumption of a battery-powered device:
The batteries are soldered to the device, and cannot be removed.
We can...
Dear Team,
i hope you are doing good,
I am working on nrf51822 controller, using SDK is 12.3.0 on windows environment. Soft-device is s130
i am planning interface...
Hi,
Wanted to interface NRF52840-DK to Board Mount Basic Pressure Sensors (Honeywell) ABPDANT005PGAA5 which is of anlog output type.Can u suggest can i go ahead with the...
