Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
My sensor uses SPI communication and need 32.768kHz external clock pin FCLK , I connect 32.768kHz clock to XL1 and XL2 but my problem is which pin can I use it for...
Hi All,
I've integrated the flash routines from this example:
github.com/.../nRF52-fds-example
into my project, and am having problems figuring out the architecture...
Hello,
I've done this with an Arduino and 1Sheeld Bluetooth LE shield, but want to try with the nRF52 dev kit. Just looking for any starter code/examples/tutorials to help...
I have a piconet of 4 devices, where 1 device is a master and 3 devices are slave.
Communication continuously occurs between master and the slaves.
But then the master...
After looking at Nordic's Bluetooth 5 implementation for nRF52840 and other chips -- it appears that Bluetooth BR classic is not available. All I see is BLE and BLE functions...
We are working on a project using nrf52832 module and GPRS device. Here we are facing a challenge in updating the firmware to BL652 over GPRS and server.
nrf52832 is connected...
Hello, a quick rundown on the problem here:
New versions of Softdevices S140 corrected an error and now correctly ignores writing to cccd descriptor using write instead...
I have 4 devices communicating in a Bluetooth piconet, where 1 device is the master device and 3 devices are slave devices.
I want to time synchronize the 4 devices to...
Hi,
I'm using the S132 v3 and wonder about the impact of DLE on scheduling.
In the chapter on Scheduling in the softdevive specification is writen that multiple peripherals...
I would like to setup the just released RasPI demo using the Nordic-Thingy52-Nodejs repo
I don't have a dongle, but 4 PDK 52840 boards and 2 Thingys.
Can I still use 1...
I found that blindly configuring all GPIO pins can stop the LFXO and RTC counter. I am reporting this as: something to be aware of, not obvious to everyone. Not a question...
I am testing the nRF52832 in Rigado BMD-301 module. I am able to get to ~40uA when advertising ,UART enabled but not used and all other peripherals disabled. But as soon as...
I connect to my BLE peripheral device using NRF connect app. While in connection, if I switch my phone's bluetooth off and turn it back again and then try to connect to my...
Hi!
I'm using the nrf52 on custom prototype boards and the official development boards. We are using the ADC to read analog values and encountered unexpected behavior related...
