I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
Hello everyone,
I have some questions regarding the active discharge of the load switch in LDO mode. We have an in-house hw with the nPM1300 configured as described in the...
HI
.
It was configured to detect low voltage of the battery using lpcomp.
This configuration is already being used in mass production of other products and there have...
Hello guys,
I was refreshing BLE concepts by doing the BLE Fundamentals once again and I have faced some trouble with the nRF5340 dk on Lesson 2. I have built the application...
Hi,
we have nRF54H20DK (SoC rev. "C"). connected to MAX77655 via I2C (SCL ~ P1.0, SDA ~ P1.4 according to I2C restriction).
I am trying to test i2c131 for reading/writing...
Hello,
We are using DFU target library with MCUboot (Connect SDK v2.9.0):
And we are getting assertion fail on first dfu_target_offset_get() call after FW update:
...
Please confirm whether the "sample app nrf5340_audio" in "v2.8.0" supports "GAIN control" in "SPI+GPIO mode". the method to enable "GAIN control" in "SPI+GPIO mode" if the...
Hi Nrodic，
Does NRF5340 have an example code for QSPI driving uLED display peripherals (for example, I need to drive this display chip: JBD013VGA， As per the attached...
I'm following along with the Nordic Academy tutorial for v2.7.0-v2.9.0. I made the recommended modifications to my v2.9.0 project with an nRF54L15-DK target:
Create sysbuild...
Hello! I am developing my own BLE solution where I have the different attributes in my service and I am connecting two different nrf52840, one to act as a GATTClient and one...
I am attempting to do a simple read from the FEM on the nrf21540-DK board. I should be able to use the zephyr driver with spi3 (or fem_spi) to do a simple read/write from...
I'm writing a client/central application connecting to a peripheral, discovering a service, and then wishing to enable notifications from a specific characteristic.
Once...
Hi,
I am trying to write a file to the FAT file system on nRF7002 board.
Here is what I have tried:
in proj.conf:
ONFIG_FILE_SYSTEM =y
CONFIG_FLASH =y
CONFIG_FLASH_MAP...
Hi,
we have nRF54L15DK (rev. 0.9.1). connected to MAX77655 via I2C.
I am trying to test i2c21 and i2c22 for writing data. I have tested it on different SCK and SDA on...
I'm following the instructions to build a co-processor using the nRF52840 dongle, on Ubuntu 22.04: https://docs.nordicsemi.com/bundle/ncs-2.9.0/page/nrf/protocols/thread/tools...
I have tried to debug my nordic5340 with VS code and it fails to load the code, although I'm able to flash the code using vs code.
when trying to track the problem using...
