Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
I've had problems during installation probably due to firewall/proxy/network protection, so I managed to install from command line as specified in Installing the nRF Connect...
I have a couple of questions regarding the operation of the nPM2100 when using the LDO in Ultra-Low Power (ULP) mode, both in active and hibernate states.
Active Mode...
I used the Nordic plugin in VS code to open the process very slowly, and the build is also very slow, it takes a few hours, I have reinstalled VS code, I have also re-downloaded...
When configuring the Bluetooth protocol for NRF5340-CLLA, should I use nrf5340dk/nrf5340/cpuapp/ns or nrf5340dk/nrf5340/cpunet when adding the build configuration, or do I...
When using the nrf52832 to scan and connect to a BLE central device, the first connection is successful. However, after the first connection is disconnected and I attempt...
Hi,
We’re developing a BLE-based product on the nRF54L15 (InsightSIP ISP2454-LX) using nRF Connect SDK v3.0.2 , with MCUboot enabled for DFU.
Our BLE application is based...
I have a custom board using a nrf5340 and am getting a 1 when trying schedule delayble work and I can't figure out why. I isolated the code to test which gets called from...
I recently updated VS Code and regret doing so. My SDK 2.3.0 was working fine for over a year. But VS Code keeps prompting me with an update. I finally updated it and I can...
I want to use the async driver,but did not find the example or explanation.
I have looked for the whole examples with "nrf_libuarte_async.h", found nothing,a little strange...
Hi, The latest version of the NRF connect VScode extension uses forward slashes in paths, which break pristine build on Windows.
The path to my sources has /V in it which...
I want to control RADIO using the TimeSlot API of nRF54L15. I have already created the code for nRF52. However, it seems that RADIO control of nRF54L15 is slightly different...
Why do I get an error when using Devicetree overlay file to delete devices The first step is to open the overlay file in the device tree as shown in the figure
...
Description:
We are qualifying a potted device which uses the nRF52840 and is intended to run in ambients up to 50 °C external air temperature .
The nRF52840 uses its...
Using latest SDK and toolchain 3.0.1, VSCode and nRF Connection Pack on Windows 11 I nearly never see a working nRF Kconfig GUI - only the first time directly after I had...
