Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi,
I just bought an NRF51-DK which I want to use with MBED. I need to download the CMSIS-DAP firmware for this board but cannot find it on the downloads page for this DK...
Hi,
i am trying to create a new model for mesh SDK 4.2.0 i am using nrf52832 please provide link or any document for creating new model, i found a link which is for SDK...
I have been using the nRF5 Mesh SDK for development and am in need of implementing single press, double press and long press on the nRF52832. I have seen the nRF5 SDK for...
Hi,
I get the error "[DFU] Remote DFU error: INVALID OBJECT. SD busy? Retrying...." when attempting a firmware update over Bluetooth.
The bootloader, application and the...
Hello,
I'm working on nRF52811, SDK16.0, Softdevice 7.0.1.
Using the pwm_driver example in the SDK, I'm trying to run a simple PWM for an RGB LED. Following is my simplified...
Hello,
I am trying to develop a product on a large scale. I need the last 4 digits of DEVICEADDR[0] as the advertising name for uniqueness. But I am not able to get it working...
I started working on power saving. I tried running the power_off sample from zephyr but there was no change in the current. The current holds the range 30mA to 32mA even after...
Hi,
I'm using saadc library to measure the voltage on nrf52832 DK. also I'm using soft device s132 on the project. I have several questions and will list below,
I want...
Dear Team,
I am trying to use nrf53840 USB dongle as sniffer. getting following error.
Reopen device failed: Timeout while waiting for device FAC66FF88C25 to be attached...
hai ,
In my application to connect 5 peripherals with central and here i am connecting with device names
static char const m_target_periph_name1[] = "Nordic_Blinky1";...
I try to send NRF_DFU_OP_PING reqeust ,then received BLE_GATTC_EVT_WRITE_RSP message. but write_rsp.len is equal to 0,.I can see gatt_status is BLE_GATT_STATUS_SUCCESS. I...
hai ,
i my application i should connect 5 more peripherals with one central .
at first i connected with peripherals mac id , mac id hard coded in central
in central...
Hi,
Is it possible to be notified when the device is entering/exiting idle? All I can see is that idle thread calling k_cpu_idle which doesn't appear to have any hooks?...
