Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi
I see i get a cmake warning with DFU enabled with the following message:
whats the purpose of this? should i just have it always enabled in my conf, or for prod...
Since of the security issue, our 9160, are connecting to a private network (10.x.x.x) by the operator. While testing the FOTA function on this private network, the 9160 has...
Working with an nrf52805. Copied a simple example (peripheral_LBS) and found that RAM overflowed by ~2.2K I note that the nrf52dk_nrf52805 is not listed as a "compatible"...
Hi Team,
I am using nRF52840_DK to program my custom board but I am facing some voltage related issue from VDD pin.
Measuring on board it's giving 3.0V for VDD & GND but...
Hi
Two questions as below
1. About nPM1300 & nRF54L15 I2C connection, at nRF54L15 side, I put SCL/SDA at P1.x group, so INT also need at P1.x group? Or I can put at P0...
https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals/lessons/lesson-4-bluetooth-le-data-exchange/topic/blefund-lesson-4-exercise-3/
There are two "Section...
Hi,
I have designed a custom board using the nRF52840 and have successfully programmed it using SWD (SWDIO & SWDCLK) with a J-Link programmer . However, I now want to program...
Hii,
Downloaded Timer code from sample and trying to build using 2.9.0 SDK but not able to build. It is building using 2.6.2 sdk.
Pls check and update soon.
Thanks...
Hello.
I started using a custom board with the nRF5340. After flashing the program, it seems that protection was enabled, and operations such as erase, read, and write became...
Hi ，Nordic team
I applied QSPI driver QSPILCD and encountered the following problems: question 1, use nrf_drv_qspi_write write data: header and tail will be a few more bytes...
I'm trying to migrate my project from the child/parent build system to the new sysbuild system in Zephyr, and I'm finding it a bit unclear. I came across a helpful post that...
I used to use ncs2.8.0, but now I have updated it to 2.9.1. I upgraded the SDK and toolchain to version 2.9.1 in VSCode, but encountered this prompt when selecting version...
Dear Sir/Madam,
In the NRF date_time_ntp.c, the fraction of the NTP message is completely ignored in the line:
* date_time_ms = ( int64_t ) sntp_time . seconds * 1000...
