Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
After updating from v2026.1.1327 to v2026.3.1484 on Linux, all previously installed SDKs disappeared from the Welcome view — the extension no longer recognizes them. Attempting...
Hi,
Recently I upgraded to nRF Connect SDK 2.6.1 and I was required to enable the GPIOTE in order to build properly. Doing this has significantly increased (nearly doubled...
Hello,
I currently have a DECT NR+ setup running on an nRF9151 based on the newer HELLO DECT sample, using v3.3.0 preview version of the modem. With these comes two files...
Hi,
1. Since I need to use PWM DMA to transfer 320 bytes of data to the PWM for sequential playback. 2. I wrote the following test example to test the nrfx pwm driver, but...
Hey there, we are currently going through regulatory testing for a hazloc product. Our product includes an nRF52805 which is used for BLE provisioning and debugging of the...
Hi,
We are investigating a Nordic BLE DFU startup failure on iPadOS and would appreciate guidance on whether this pattern is known at the CoreBluetooth / iOS DFU layer...
How to change the parity bit on UART on NRF54L15?
prj.conf includes:
CONFIG_SERIAL=y CONFIG_UART_20_NRF_PARITY_BIT=y
DT overlay includes:
&uart20 { parity = "even...
Latest nRF connect for VS code seems to ignore Toolchain manager install dir under certain conditions.
nRF connect output displays " Error: Install directory 'C:\ncs' not...
Hi We are using nPM2100 with PG/RESET mapped to SHPHLD. We are using Zephyr library to manage the nPM2100. We put the device into hibernate with a timed wake up, if we wake...
Hi everyone! I wrote code in arduino IDE but wanted to use all potential of Xiao NRF52840 with use of Nordic SDK and Zephyr RTOS as well as zigbee on my small side project...
Device: nRF51822_xxac; the Nordic-supplied NUS application worked after I figured out the softdevice and application loading sequence.
Development platform: Mac OS Tahoe...
On lesson https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals/lessons/lesson-4-bluetooth-le-data-exchange/topic/blefund-lesson-4-exercise-3/ , When trying...
Hi.
I'm developing a BLE peripheral application running on nRF54L15. nRF Connect SDK v3.2.1 with SoftDevice Controller is used for my application. As the title says, following...
Dear Nordic team,
We are using the nRF54L15 QFN52 package on our custom device and are using the P0.06 and P0.00 for the TX and RX, respectively, for our UART service interface...
