Hello Noric Dev Zone members,
we are looking for a Firmware developer supporting us in bringing Hyko to our customers.
What we are working on is making energy heroes in...
It would be very helpful to hear of others experiences getting these licenses, also I would like to find out if anyone has any advice of anything to be included or excluded...
I wanna implement this code for the app inventor, but there was several problem here. I can't use array or index for developing my trapezoidal method.. like this..
code...
Hello,
We are looking for a developer a single task project. We need to provide all of our developers with the same development environment, so we are looking for someone...
I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
Hello,
We are currently developing a project based on the nRF52832 SoC, where two external sensors are connected:
Proximity Sensor: VCNL4040
Accelerometer: LIS2DH...
Hi
I was initially using Window 10 Laptop with nrf52832 ncs2.9.0 in visual studio code....I developed a ble application with mcuboot (over ble - reference nrf academy tutorials...
Hi,
1. The customer has two projects that both require the use of mcuboot. However, for these two projects, the source code and configuration of mcuboot need to be modified...
Hi, I'm working on a custom board with the nRF54L15 using NCS 3.2.1, and have configured spi21 on port 2 for a display. SPI pin configuration: SCK: P2.06 (TRACECLK) CS: P2...
I am working my way through the DevAcadmy (nRF Connect SDK Fundamentals) using an nRF52840 development kit.
In lesson 6, exercise 1, I try to get an I2C with a BME280 to...
In sdk-zephyr/samples/boards/nordic/battery/src/battery.c at main · nrfconnect/sdk-zephyr
nRF54L series doesn't have 'SAADC_CH_PSELP_PSELP_AnalogInput0', how should it be...
I am trying to interface an SD card over SPI on nRF54L15 using nRF Connect SDK .
I started from Nordic’s fs_sample , which by default uses SPIM20 on Port 1 pins , and this...
I am using SEGGER Embedded Studio v8.26 with J-Link software v8.94 on Windows (64-bit) for BLE development on the nRF52840 DK .
Using J-Link Commander , I am able to:
...
After upgrading my NCS version from 3.1.1 to 3.2.0 for the nRF54L15, I found that the GRTC resets after a sys_reboot(), whereas it didn't in the previous version. What changes...
Hello everyone. I'm using the nRF52840 Pro Micro board with the J-Link programmer and the nRF Connect extension for VS Code. This board comes with a U2F bootloader, but I...
I use a hardware timer to capture/compare incoming pulses using PPI to trigger the captures from GPIOTE. I previously wrote the same application for nRF52832 on the old SDK...
When running SLM on nrf91, it sends "Ready\r\n" over UART on boot/reset. On nrf54, we use "Ready" to detect reboots and rerun the setup. However, when the modem reboots, sometimes...
Hello Team,
I am using the nrf54l15 custom board for development. I have configured the P1.06 as a normal GPIO as follows:
And using it as follows:
The pin status...
I use example from nrf52 SDK. project path:nRF5 SDK\nRF5_SDK17.1\examples\ble_peripheral\ble_app_uart\pca10040e\s112\arm5_no_packs.
emulator: ST link V2
but no target...
Hello,
The nRF5340 supports audio transmission, while the nRF54L15 supports Channel Sounding. Is it possible to conduct audio transmission simultaneously with Channel Sounding...
