Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hi,
I am using 2 x AA batteries which gives 3V. Planning to enable all the internal LDOs (1.2V, 1.8V and Radio LDO).
VDD and AVDD are shorted on Board.
Will the device...
Is there a porting guide to this?
Custom hardware
Central device
SDK V11
I'm getting a reset in client_handling.c::ble_stack_init();
Right after I set the clock as...
Even I am writing BLE applications, but I don't totally understand these items:
In Characteristic Properties of GATT Characteristic metadata
We have read, write, notify...
I am trying to trigger some functions based on some pre-determined timings. I tried to do that using nrf_delay_us and also using timer0 interrupts, but both are giving me...
Hi,
I'm using nRF Master Control Panel to test a Phone Alert Profile (PASP) I've implemented. For this, in the app I configured a GATT server that exposes the Phone Alert...
Hi,
I am using nRF5_SDK_11.0.0 to learn how to use BLE stack to communicate.
For the BLE HRS app, I want to achieve sth. like this:
Central node can configure the sending...
Hi,
I'm not sure if this forum support that board but if YES, can You explain how to upload some program on that board. I think that process is little bit different that...
For some of the examples i see different versions
For example the ble_app_hts example
It has a _hci, _spi and a _uart version
In the documentation i don't find any info...
hello everyone！
I have just contact nrf51822, the agreement with the application framework is not very familiar with, you can share a quick start of the information, the...
Hi everyone,
Where I can read transmission type and device number of connected ANT+ device (HRM)? I want save those values and bound later only with currently connected...
I tried to set a custom key in this way:
... ANT INIT
uint8_t network_number = 2;
uint8_t p_network_key[8] = {0xa1, 0x15, 0xb3, 0x66, 0x60, 0xef, 0x19, 0xa1};
err_code...
Hi there.
I'm woking with sensor in board nRF51822.
Do we have any tool to test oscilloscope i2c?
I want to check the signal is same as what I sent or not.
Thanks...
Since nRF51 is multi-protocol, why don't Nordic provide support for Zigbee? This way, customers can simply buy one single chip and have several standards supported. Are there...
