Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
I need to save energy for my ble application. So I turned off the sensor when there was no ble connection. A ble connection is a condition for me to turn on the sensor, but...
How exactly are the UART pins selected for the nRF9160? I've searched and am unable to find a file to configure pins. I need to change to pins from the development board to...
Hi,
I'm working with the SAADC on an NRF52832. I'm using the SAADC driver from SDK15.2.
I have a problem with the calibration routine because it's generating DONE events...
Hello,
I am developing an application on the 52840 and so far find the SDK documentation quite confusing and somewhat contradictory. I need to write a simple TWI (I2c) master...
Hi, I’m located in Liège, BELGIUM.
Using the nRF9160DK, an orange SIM card, MODEM firmware mfw_nrf9160_0.7.0-15.alpha I managed to make run some sample code:
mqtt_simple...
Hi. I'm using nRF52832, SDK13.0.0.
The roll is peripheral.
And I'm using Oberon to use ECDH.
I think you have the result or document for random generator's performance...
The nRF9160 DK I'm working on does not seem to be able to connect to nRF Cloud after following the tutorial:
https://www.nordicsemi.com/Software-and-Tools/Development-Kits...
Apologies, I accidentally closed and opened my previous ticket: https://devzone.nordicsemi.com/f/nordic-q-a/53073/unable-to-add-lte-device-on-nrf-cloud , can I check that...
The new SDK has no documentation on this functionality: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v12.0.0%2Fgroup__ble__radio__notification...
Where to get this RaspPi_OT_Border_Router_Demo_v3.1.0-1.alpha.img file.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.thread_zigbee.v2.0.0%2Findex...
Hello
I need urgent help. From days I have been stuck exploring NRF SDK 15.0 to do a simple task.
I am using an NRF DK board PCA10040. After going through peripheral drivers...
Hi,
I am working with central and peripheral uart example and facing with connection problem between two boards.After debugging at the central side i am getting error in...
Dear Sir/Madam,
We have a customer to develop a product based on nRF51422 and then they passed their product for pre-registration test.
They used DTM interface to connect...
Hello
I have nRF52832 custom board and have BME280 sensor connected to I2C/TWI
Whatever I do I get same reading (for 3 different sensors)
I'm constantly reading same...
Hello, I would like to use nRF24AP2 in a SPI bus with an accelerometer (a slave peripheral). I need that the host works as master with accelerometer. But in this way we will...
