Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Good day,
I am starting a new project where I am using the ANNA-B112 BLE device from ublox in a custom design. The ANNA-B112 interfaces with a host MCU over UART. I would...
Hi,
I have added nus service to the relay central and peripheral example.The relay board advertises and i can connect to the peripheral part of device through the nrf connect...
The mesh health model state is not restored following a reboot in the current version of the Mesh SDK using the light switch example.
According to the documentation, the...
Hello folks, I am new to Thingy 52 PCA 20020 model and I have downloaded nRF SDK 15.2 and I am using a Segger J-Link programmer/debugger. The thing is I would like to get...
In acces.h there is the publish period format definition, which is
/** * Model publish period structure. */ typedef struct { /** Step resolution. */ uint8_t step_res : ACCESS_PUBLISH_STEP_RES_BITS;...
Hello,
I was surprised that gcc did not optimized my strlen("FOO") construct (worse, in a code review, I argued that the compiler would do the optimization…)
It seems...
Hey there,
I am trying to develop with the Bluetooth Mesh SDK for NRF5.
We have two chips, NRF52840 and NRF52840/NRF52832and are using the light_switch example from the...
I need to save energy for my ble application. So I turned off the sensor when there was no ble connection. A ble connection is a condition for me to turn on the sensor, but...
How exactly are the UART pins selected for the nRF9160? I've searched and am unable to find a file to configure pins. I need to change to pins from the development board to...
Hi,
I'm working with the SAADC on an NRF52832. I'm using the SAADC driver from SDK15.2.
I have a problem with the calibration routine because it's generating DONE events...
Hello,
I am developing an application on the 52840 and so far find the SDK documentation quite confusing and somewhat contradictory. I need to write a simple TWI (I2c) master...
Hi, I’m located in Liège, BELGIUM.
Using the nRF9160DK, an orange SIM card, MODEM firmware mfw_nrf9160_0.7.0-15.alpha I managed to make run some sample code:
mqtt_simple...
Hi. I'm using nRF52832, SDK13.0.0.
The roll is peripheral.
And I'm using Oberon to use ECDH.
I think you have the result or document for random generator's performance...
