hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi, In my project we are using the ESB between a nrf52811 and a NRF5340dk and are trying to evaluate the maximum speed we can reach with ESB packet transmission without acknowledge...
Hi Nordic team:
I am configuring a low power application for the nrf52833 board (custom board). This is a very low power application and I want the board to stay on sleep...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
For the Pawr example I refer to E:\NCS\v2.8.0\zephyr\samples\bluetooth\periodic_adv_rsp and periodic_sync_rsp.
Advertiser...
I have compiled code that debugs and runs normally on the nRF52840DK. I just connected my custom PCB to the debug out connector on the DK and I have two issues that are probably...
I just flashed a new image on my device using MCUmgr. In the logs, when the device boots up, it shows the correct APP_VERSION string.
returns:
I: Firmware version: 0...
Hi, We are trying to provide example support for our RAK4631 (nRF52840 based) and an ultrasonic PDM microphone (RAK18032). We have been able to get a sample frequency of 100...
Hi, I am using nRF5340 for my unicast Audio server example where the nRF5340DK is the headset and my mobile device is the audio source. I have taken the unicast audio server...
Hi,
I just can not download nRF_DeviceFamilyPack 8.44.1 from this link developer.nordicsemi.com/.../ It comes up an error of the server. Does any body knows how to get this...
I'm following the tutorial Exercise 1 – Custom board for single-core SoC using ncs v2.9.0 with one slight difference in that I'm using a nRF52DK with nRF52832 because that...
I built a custom board with the nrf5340 and a SD card connected to non-standard gpios. My SD card is connected via SPI over the P0.14, P0.15, P0.16, P0.17, respectively for...
The latest toolchain has removed "serverArgs": from debug configuration in nrfConnect 2025.4.106
Is is mandatory as we only have RTT on our FF board and no serial...
Hello everyone,
I am trying to test the SLM on the nRF9160DK on NCS 2.9.0. (SDK and toolchain) I want to control the nRF9160 with an external MCU, so for this the application...
Hello,
Our product that we currently design is based on the nRF52840 QFAA and w e are looking to achieve FCC, CE and RED compliance.
I would like to request any certificates...
Hi,
I'm working with the nRF54L15 SoC and running into an issue when using UARTE21 together with SMP over Bluetooth . Here's what I’ve observed:
UARTE21 works perfectly...
