Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hey guys,
I am using NRF51DK board and SDK v12. I want to add MPU6050 library to fatfs example but I have some problems. When i add "mpu6050.h" to my project i get "Not...
Hi,
I'm using NUS service on nRF51822 with SDK 12.3 .
I want to secure the communication between the nRF and the mobile application.
So, I want to know the different...
NRF51822
SDK12.3
keyboard demo code
After each delete match at the PC end，None of the broadcasts are searchable。Then I Google the content like this。
I wonder...
Hello,
I am using NRF52840 in my System. We like the USB access on NRF52840 and would like to use it. However, I don't need BLE in my application. Can I leave the Radio...
Dear All,
i want to make a product which using nrf24le1 chip, but now i'm stuck on the antenna impedance matching issue.
i'm not very familiar with the antenna design...
I'm try to using Nordic 52832 board to send hexadecimal to the phone, but it still receive for ascii.
Using example\ble_peripheral\ble_app_uart code for sending.
Hello
We have a project of energy meters with mesh network.
There are some parameters important for us:
Time of reconfiguration
size of network
connection range...
When I plug the kit into a USB slot on my computer, the nRF52 DK does not appeared as a removable drive named "JLINK" as it should according to the documentation. Has anybody...
I m working on SDK-11, and using sample program experimental_ble_app_blinky, in this code I want to read RSSI value and want to show on NRF Connect app. But its not showing...
Hello,
We are using nRF52832 DK, nRF52 sdk15.0 with SES IDE in windows 10. Currently we have senor network which is trigger every 1 Hr and send data trigger time set in...
The hardware is a custom board with a Rigado BMD300 module (which uses the nRF52832). I am using Softdevice S132.
My code base started as the ble_app_uart peripheral example...
Good afternoon,
In my peripheral application (SDK15 and Softdevice6.0.0) I can have several bonded central peers but only 1 can be selected on demand for the whitelist...
Dear all
Does the nRF52840 provide an unique device address (MAC) address, or that address has to be provided by the application layer to the stack/chip ?
Regards...
I am inquiring about the range of the nRF52840 USB dongle. I see a meandering antenna on the PCB. This is different from the DK's and am wondering if the meandering antenna...
