Hello!
I am working to design and build a custom PCB using the nRF7002 chip and came across this callout on the schematic diagram and wanted some clarification about it...
I will attach my main.c and skd_conifg, maybe i'm overseeing something in code. Also i will attach schematics and pcb. I'm aware of RGB led consumption, in reality it's around...
Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
Hi Nordic Team,
I would like to confirm whether enabling APPROTECT also implicitly enables Secure APPROTECT, or if these two protection mechanisms need to be configured...
Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
Hi there,
I have two type nRF52 DK, pca10040 and pca10056. I know that pca10040's maximum txpower is 4dBm and pca10056's maximum txpower is 8dBm, and both boards have CR2032...
In file nfc_fixes.h, SDK 15.0.0:
#ifdef BOARD_PCA10040 // assume nRF52832 chip in IC rev. Engineering B or Engineering C
#define HAL_NFC_ENGINEERING_BC_FTPAN_WORKAROUND...
Hi,
I read a lot of questions but problem still wasn't fixed. Random disconnect have the period 5-10 mins. The problem with s132 or s130 v2.0.1 and LG G3 android 5.0....
Does anyone know when will ANT SoftDevice be available for nRF5 SDK v15? Accordign to https://www.thisisant.com/developer/components/nrf52832#tab_protocol_stacks_tab, only...
Hi
I try to communicate with my NRF24L01+. For this, i have connected a mikrocontroller to my Module. Actually i am using a small piece of code, which allows me to send...
Hi,
In my project, I use button for put on the microcontroller in sleep mode. I implemented one timer that when I press more of 5 second the button, the micro call sleep_mode_enter...
Hi,
I have included in my code the code from the twi_scanner example as a starting point for using TWI in my board. When compiling, I get the following error:
../.....
hi,
Please Refer Light Switch Client Example in Mesh 2.0
I would like to know Code where and in which File the UUID from the unprovisioned Node is captured ?
Thank ...
Hello,
What is the switching frequency of the buck regulator integrated into the nRF51822?
The characteristics of this regulator do not seem to be explained in the documentation...
I'm following the Custom BLE Service Example , and using:
Segger Embedded Studio Release 3.34a
macOS 10.13.4 (aka High Sierra)
nRF52 DK (PCA10040, nRF52832)
nRF5_SDK_15...
Hi,
I am investigating an alternative to an implantable device that currently uses NFC.
The device range would only be about 3m and the data would only be transmitted...
this packet is capture by wireshark .I use nrf51822 and sdk12.3 connect Balance car,but the packet not have LL_VERSION_IND, LL_FEATRUE_REQ、and LL_Connect_UPDATA_REQ these...
Dear Nordic Team,
Thanks for supporting.
now i am workwith secure dfu. I followed this link https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure...
hello
I am just starting to use the nrf52832 .
I design the PCB with nrf52832 and want to load the softdevice.The nrf go studio can not detect the nrf52832, but the keil...
